HOW TO REVERSE LOCK
1
C
HECK DOOR PREPARATION
A. Clean out lockbody pocket in edge of
door to assure it is clear of debris. For
Triad Lock also clear debris from
hookbolt pockets and track in edge
of door.
2
I
NSTALL LOCKBODY
A. Insert lockbody (and
hookbolts for Triad) into door
prep. Check that lockbody fits
easily in door with screw holes
aligned. Secure lockbody to the
door using lockbody screws.
Do not tighten fully at this time.
If a cylinder is not included in your lock
function, proceed to step 7
3
I
NSTALL OUTSIDE ESCUTCHEON ASSEMBLY
B.
Important
Insert spindle
into retaining
nut to secure
this position.
4
I
NSTALL INSIDE ADAPTER
&
PLATE ASSEMBLY
A. With outside escutcheon
assembly in hand tighten
the retaining nut against
the mounting plate as far
as it will go by hand. To
insure a tight fit in this
assembly, back off
retaining nut
just one
notch
, until star pattern
aligns with square
corners. (see pattern
shown)
C
A. With adapter and plate
assembly in hand
repeat
important steps 3A and
3B
as above. For retaining
nut and spindle only.
B. Insert spindle with
adapter and plate into
square hole in lockbody
on inside face of door.
C.
Secure adapter and plate
with thrubolt screws making
certain the lock washers are
attached before tightening
screws into thrubolt post of
the outside rose assembly.
Do not over tighten.
5
I
NSTALL INSIDE ESCUTCHEON
6
S
ECURE CYLINDER
(
IF PROVIDED
)
A. Lay inside escutcheon
flush against door face
and screw the inside
escutcheon to the outside
escutcheon using trim
screws.
Do not over tighten.
7
I
NSTALL INSIDE LEVER
/
KNOB
B
Set Screw - Proper Location
Lever/Knob
Note: This plate assembly
will be circular in shape
on KW1 and LW1 trim
Escutcheon/Rose
Face of Door
INSIDE
INSIDE
OUTSIDE
OUTSIDE
LEFT HAND
LEFT HAND
REVERSE
BEVEL
RIGHT HAND
RIGHT HAND
REVERSE
BEVEL
DOOR HANDS DETERMINED FROM OUTSIDE
DOOR HANDING
Inside Adapter
C
A
C
B
D. If LE3 or LE4 trim design
skip to step 6. With
outside lever in the
horizontal orientation,
as shown, carefully insert
the mounting posts
through the door and
lockbody, making sure
the spindle is engaged in
the lock. Outside
escutcheon assembly
should be flush with
door surface.
A.
Single Cylinder
: Screw cylinder, along
with cylinder spring and blocking ring
behind it (if provided), into escutcheon
and lockbody.
Double Cylinder
: Screw both cylinders,
with cylinder spring and collar behind,
into lock so that the cams within the
lock do not touch while the cylinder
face lays flush with collar edge, when
collar is held against the escutcheon
face. Note: It is easier to use a key,
slightly out of position in cylinder, to
help screw the cylinder down
completely. Over tightening cylinder
could cause malfunction in lock.
B
A. Place inside lever/knob horizontally
onto spindle. Position lever/knob
edge so it is 1/16" from inside
escutcheon face. Hold lever/knob in
place while securing with set screw.
B. Lever/knob set screw must rest in
groove on inside adapter for proper
installation. See illustration.
C. Pull on lever/knob to test if set screw
is properly secured.
A
A
B. Secure cylinder in place by tightening the
cylinder retainer through hole in edge of
door (shown) with Phillips screwdriver.
C. Test cylinder for proper operation. If LE3 or
LE4 trim design, return to step 3 to continue.
D. Now tighten the lockbody screws completely.
E. Secure the outside front plate to the
lockbody with front screws.
F.
For LE2 or LE4 trim designs, attach outside
escutcheon with small set screws using allen
wrench.
C. If a thumbturn
tail piece is
attached to both
the inside and
outside escutcheons,
make both tail pieces
shorter by snapping them
off at the seam.
Important: Test lock for all operations before closing the door.
Spindle
red color
locking piece
Note: Red color indicates locked side of door
or hold back side (91 and 92 Function).
A7031D
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY
Group company. All rights reserved. Reproduction in whole or in part without the
express written permission of Sargent Manufacturing Company is prohibited.
A7031D
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY
Group company. All rights reserved. Reproduction in whole or in part without the
express written permission of Sargent Manufacturing Company is prohibited.
