INSTRUCTION MANUAL
VDC-D1785IRVP
Vandal-resistant IR Dome Camera
About this manual
Before installing and using the camera, please read this manual
carefully. Before to keep it handy for later reference.
Dimension:mm (inches)
Depending on the conditions of use, installation and environment, please be
sure to make the appropriate settings and adjustments. If you need help with
installation and or settings, please consult your dealer or authorized Sanyo
Service Center.
TROUBLESHOOTING
Before sending the camera out for repair, check the items below.
If the problem persists after checking these items, consult your dealer or
authorized Sanyo Service Center.
If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens been adjusted correctly (with level volume)?
Is there adequate illumination?
If the image is unclear
Is the monitor adjusted correctly?
Is the lens in focus?
Is the lens clean?
Dirt or
fi
ngerprints on the lens can adversely affect the image. Gently wipe and
dirt of fingerprints off the lens a soft cloth or lens cleaning paper and cleaning
fl
uid (commercially available).
SERVICE
The camera is precision instrument. Handle it carefully and always follow the
safety precautions. If the camera requires service, never try to repair it yourself
or open the casing. For servicing, maintenance, or repairs, consult your dealer
or authorized Sanyo Service Center.
For EU Users
Please note:
Your SANYO product is designed and manufactured with high quality
materials and componets which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-
life, should be disposed of separately from your household waste.
Please dispose of this equipment at your local community waste collection/
recycling centre.
In the European Union there are separate collection systems for used
electrical and electronic product.
Please help us to conserve the environment we live in!
This symbol mark and recycles system are applied only to EU countries and
not applied to countries in other areas of the world.
SANYO FISHER Sales (Europe) GmbH
Stahlgruberring 4, D 81829 Munich, Germany
SANYO Electric Co., Ltd.
1-1, Sanyo-cho, Daito City, Osaka 574-8534, Japan
For Russian Users
This product certi
fi
ed by of
fi
cal certi
fi
cation company which is
authorized by Russian Federation.
ДЛЯ
ПОЛЬЗОВАТЕЛЕЙ
РОССИИ
Данная
продукция
сертифицирована
официальным
МО
04
органом
по
сертификации
Российской
Федераци
.
SPECIFICATIONS
Appearance and speci
fi
cations are subject to change without prior notice.
PRECAUTIONS
■
In case of a probelm
Do not use the unit if smoke or a strange odor comes
from the unit, or if it seems not to function correctly. Turn
off the power immediately and disconnect the power
cord, and then consult your dealer or an Authorized
Sanyo Service Center.
■
Do not modify
Do not modify the cabinet and camera, as it maybe
dangerous and cause of damage to the unit. For repairs,
consult your dealer or an Authorized Sanyo Service
Center.
■
Do not put objects inside the unit
Make sure that no metal objects or
fl
ammable substance
get inside the unit. If used with a foreign object inside, it
could cause a
fi
re, a short-circuit or damage. Be careful
to protect the unit from rain, sea water, etc. If water or
liquid gets inside the unit, turn off the power immediately
and disconnect the power cord, and then consult your
dealer or an Authorized Sanyo Service Center.
■
Be careful when handling the unit
To prevent damage, do not drop the unit or subject it to
strong shock or vibration.
■
Do not install this unit close to magnetic
fi
elds
The magnetic
fi
elds may result in unstable operation.
■
Protect from humidity and dust
To prevent damage, do not installl the unit where there is
greasy smoke or steam, where the humidity may get too
high, or where there is a lot of dust.
■
Protect from high temperatures
Do not install close to stoves, or other heat sources, such
as spotlights, etc., or where it could be subject to direct
sunlight, as this could cause deformation, discoloration or
damage.
■
Cleaning
* Dirt can be removed from the cabinet by wiping it with
a soft cloth. To remove stains, wipe with a soft cloth
moisteried with a soft detergent solution and wrung dry, then
dry by wiping with a soft cloth.
* Do not use benzine, thinner or other chemical products
on cabinet, as this may cause deformation and paint
peeling. Before using a chemical cloth, make sure to read
all accompany instructions. Make sure that no plastic or
rubber material comes into contact with the cabinet for a
long period of time, as this may cause damage or paint
peeling.
■
Degree of protection: IP67
This unit has been certi
fi
ed to IP67 standards when properly
installed. Use only an IP67 certified enclosure or an
electrica box. Ensure all openings in enclosure are sealed
as per manufacture's instructions.
Sanyo Electric Co., Ltd
Printed in Taiwan
CAUTION
Since the conduit hole cover is not waterproof-
finished, always be sure to seal the cover entirely
by caulking, for example, upon completion of
installation.
Make sure to perform waterproo
fi
ng properly to the
ceiling or wall where you are installing the unit.
When setting up this camera, make sure that it
is installed securely. Check that the installation
location is strong enough to bear the camera
unevenness. In addition, do not touch the camera
unit except when settings and adjustment are
necessary.
1.
Loosen the 3
fi
xing screws using the supplied
hexagonal wrench and remove the dome cover.
2.
Inceiling : Place the supplied "Mounting template
for inceiling" on the mounting surface, and mark 3
positions shown in.
or
Surface : Place the supplied "Mounting template for
surface" on the mounting surface, and mark 4 positions
shown in.
3.
Drill holes at positions as marked and insert the
supplied screw holes in the holes.
4.
Cut a hole in the ceilling or the wall for routing the
cables.
5.
Pass the power cable, video cable and UTP cable
from the camera unit through the cable hole in the
ceilling or the wall.
6.
Align the unit mounting holes of the camera unit with
the holes in the ceilling or the wall.
7.
Secure with the supplied mounting screws.
8.
Carry out the settings and adjustments for the
camera. Refer to "CONNECTIONS AND SETTINGS"
for camera settings and lens adjustments.8.
* When routing the cables on ceiling or wall surface:
Loosen the conduit hole cover
fi
xing screw on the back
of the camera unit base with the hexagonal wrench,
open the cover, and pass the connection cables
through the conduit hole.
HINT
(#1) Press the grip portion to remove the mask before
adjustment.
INSTALLATION
For Inceiling Mount
installation
-Inceiling type-
For Surface Mount
installation
-Surface type-
Model Number
VDC-D1785IRVP
Scanning system
PAL standard 625 lines, 50fields/sec.
Image sensor
1/3" Interlace CCD sensor
Number of effective pixels
752(H) x 582(V)
Horizontal resolution
540 TV lines (Typical)
Lens
f=3.7 to 12mm, F1.4, IR lens
Minimum illumination (50IRE)
0.7lx LED-Off, 0.0lx LED-ON
Video/ Monitor output
1.0Vp-p (75ohms, composite)
Video S/N ratio
More than 48dB
Day & Night
True Day/ Night
Backlight compensation
ON/ OFF
White balance
Auto
Auto iris drive
DC
AGC gain
ON/ OFF
Flickerless
ON/ OFF
Gamma correction
0.45
Sync system
Internal
Unshielded Twisted Pair
Passive type
IR LED
18 pcs
IR distance
20m
IR wavelength
850nm
Operating temperature
-10°C to +50°C (14°F to 122°F)
Operating humidity
Less than 90% (no condensation)
Power supply
12VDC+/-10%, 24VAC+/-10%, 50Hz
Power consumption
7.0w
Weather Protection class
IP67
Dimensions (
ĭ
x H)
150.1 x 129mm (5.9" x 5.1)
Weight
Approx. 0.95kg(33.5oz) In-ceiling mount
1.20kg(43.7oz) Surface mount
1.Wall Mounting template……. .…..1
2.Inceiling Mounting template… .…1
3.Installation Manual……… . .….…1
4.Conduit cap……………… .……...1
5.Fixing screw (P4*31TP)….……...4
6.Wall plugs…………… ...…….…..4
7.Fixing scerw (M4x0.7P x15mm)..3
8.Monitor out cable…………………1
9.Hexagonal wrench……………..1
10.Surface-mount adaptor………..1
Accessories
(#1)
(B)
(A)
(C)
(D)
(E)
(F)
