2
HDMI
3
HDMI
HDMI
(DVI)
INPUT1
(MONO)
(VIDEO)
VIDEO
VIDEO
INPUT
VIDEO
INPUT
1
2
AUDIO
(MONO)
DIGITAL
AUDIO
OUTPUT
Please read before operating your HDTV!
PROTECTING THE LCD-
LED SCREEN
CAUTION:
The screen can be damaged if
it is not maintained properly.
• Do not use hard objects such as hard
cloth or paper to clean the screen.
• Do not use excessive pressure when
cleaning the screen; excessive pressure
can cause permanent discoloration or
dark spots.
•
NEVER
spray liquids on the screen.
HANDLING PRECAUTIONS
• Handle by the cabinet only.
• Handling by two or more people is rec-
ommended.
• Never touch the screen when handling.
• Handling damage is
not
covered under
warranty.
• Do not remove the protective film
covering the front cabinet while
handling the HDTV.
POSITIONING THE HDTV
• Always use a firm and flat surface when
positioning your HDTV.
• Do not position the unit in a confined
area.
• Allow adequate space for proper venti-
lation.
• Do not position the HDTV where it is
easily reachable by small children and
may present risk of injury.
• Once HDTV is positioned, remove the
protective film covering front cabinet.
SPECIFICATIONS
Power Requirement:
Source: AC 120V, 60Hz
AC Power Consumption:
90 watts
Weight:
31.2 lbs (without stand)
Dimensions _________________________
WIDTH HEIGHT DEPTH
w/stand
38.9
24.7
7.7
w/out stand
38.9
23.7
2.9
NOTE: Dimensions are in inches
GETTING STARTED
Hook up your antenna or your cable
service to the HDTV’s
ANT
terminal
with the use of a 75 OHM coaxial cable.
NOTE: Keep your indoor antenna at
least 3 ft. away from the televi-
sion set and any other electron-
ic equipment.
The tuner in this HDTV can receive
:
•
Digital and Analog off air signals
from an antenna
•
Analog or ClearQAM cable channels
from a direct Cable TV connection.
ANTENNA CONNECTION FOR
OFF-AIR SIGNALS OR CABLE
ANTENNA
CABLE
ANALOG / DIGITAL
ANTENNA IN
AV INPUT SELECTION
Press the
INPUT
key to select the
correct AV input for the video source
you wish to watch.
NOTE: Unused AV inputs may be dis-
abled with the Input Setting feature.
Finish Setup
Repeat
Channel Search Result: Succesfully Completed
If you are having problems, call us toll-free at 1-800-877-5032
Analog Channels
Video 1
Video 2
HDMI 1
HDMI 2
Digital Channels
16
26
HDMI 3
Before proceeding, please make
sure to correctly hook up your
antenna or cable connection and
all AV equipment to your HDTV.
1. PLUG IN AC POWER CORD
120V AC, 60Hz
2. TURN ON TV
3. TV SET LOCATION SELECTION:
Select “
Home Mode
” to set the
HDTV’s backlight to an Energy Star
qualified level, or select “
Store
Mode
” to set the backlight to a retail
display level.
4. CHANNEL AND SIGNAL SEARCH:
Select “
Signal Search
” and press
ENTER
to perform a channel search
from an Antenna or a direct Cable
connection, and a signal search
from devices hooked up to the
HDTV’s AV input jacks.
5. SIGNAL SEARCH RESULT SCREEN
The final setup screen displays ana-
log and digital channels found, as
well as AV inputs detected.
Select
Finish Setup
and press
ENTER
.
NOTE: If you wish to repeat the
process, select Repeat.
INITIAL CHANNEL SEARCH
Need help?
www.sanyoctv.com 1-800-877-5032
Need help?
www.sanyoctv.com 1-800-877-5032
1JC0P1P0015 - -
Part No.:
Owner’s
Manual
(English)
© 2012 Sanyo Manufacturing Corporation
1080p HDTV LCD
42” LED
1080p HDTV LCD
Model No.:
DP42142
As an Energy Star
®
Partner,
Sanyo Manufacturing Corporation
has determined that this product
meets the Energy Star
®
guide-
lines for energy efficiency.
ENERGY STAR
TRADE
M
ARKS
________
Manufactured under license from Dolby
Laboratories. “Dolby” is a trademark of
Dolby Laboratories.
HDMI, the HDMI Logo and High-Definition
Multimedia Interface are trademarks or regis-
tered trademarks of HDMI Licensing LLC in
the United States and other countries.
Manufactured under license from Audyssey
Laboratories. U.S. and foreign patents pending.
Audyssey Dynamic Volume
®
is a registered
trademark of Audyssey Laboratories.
HDTV INPUT/OUTPUT REFERENCE ________________________________________
4
6
HDTV BACK PANEL
HD
M
I (INPUT1, INPUT2 & INPUT3)
Use
HD
M
I INPUT1, 2 & 3
to hookup HD digital devices such
as a Blu-ray player, HD Cable Box, HD Satellite Receiver or
Video-game System.
Connect your digital device’s HDMI output to any of the
three (3) HDMI inputs on your HDTV with the use of an HDMI
cable.
NOTE: A DVI connection is possible via the HDMI (DVI) INPUT1
using an appropriate cable or adapter and connecting the
audio to the AUDIO mini stereo jack.
Analog / Digital Antenna Input
Hook up your indoor or outdoor digital antenna, or a direct
Cable service (Analog or ClearQAM).
USB
USB
input jack is used to connect a USB mass storage
device to watch digital images stored in JPEG format.
AUDIO mini stereo jack (3.5mm)
For AUDIO signal from DVI device (using HDMI INPUT1).
Digital Audio Output (Coaxial)
Hookup a multichannel receiver with the use of a phono-
type digital audio cable.
VIDEO INPUT1
(CO
M
POSITE)
Yellow (Video), plus white and red (Audio) input jacks.
CO
M
POSITE
connections are used to hookup your analog
equipment such as a VCR or an older DVD player.
NOTE: Match the color of your device’s output jack, the con-
nector and the HDTV’s input jack.
VIDEO INPUT2
(CO
M
PONENT)
Green (Y), blue (Pb), and red (Pr) Video inputs plus the
white and red Audio inputs.
CO
M
PONENT
connection will accept SDTV, EDTV and
HDTV video signals. Use it for great image quality from di-
gital devices such as a DVD player or Video Game system.
Match your digital device’s Component output jacks to the
Component input jack set (VIDEO2) on your HDTV.
NOTE: A composite connection is possible via VIDEO INPUT2
using the Y (VIDEO) jack and the L/R audio jacks (see
Video2 Setting.)
1
2
3
4
5
6
7
Printed in Mexico, April 2012
US2J / 42-Z5GH / GXBM
Sanyo
M
anufacturing Corp. 3333
Sanyo Road, Forrest City, AR 72335
2
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit fully into your out-
let, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched par-
ticularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate nor-
mally, or has been dropped.
15. If an outside antenna is connected to the television equipment,
be sure the antenna system is grounded so as to provide some
protection against voltage surges and built up static charges.
In the U.S. Selection 810-21 of the National Electrical Code pro-
vides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes,
and requirements for the grounding electrodes.
16. An outside antenna system should not be located in the vicini-
ty of overhead power lines or other electrical light or power
circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or cir-
cuits as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING ACCORDING
TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
“Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the build-
ing, as close to the point of cable entry as practical.”
17. Wall or Ceiling Mounting—The product should be mounted to
a wall or ceiling only as recommended by the manufacturer.
18. Apparatus shall not be exposed to dripping or splashing, and no
objects filled with liquids, such as vases, shall be placed on it.
19. When the MAINS plug is used as the disconnect device, the
disconnect device shall remain readily operable.
RISK OF ELECTRIC SHOCK DO NOT OPEN!
CAUTION: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT RE
M
OVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK
OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTE-
NANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
M
OISTURE.
I
M
PORTANT SAFETY INSTRUCTIONS
CAUTION
FCC INFOR
M
ATION
________________________________________________
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gen-
erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm-
ful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION
: FCC Regulations state that improper modifications or unauthorized changes to this unit may void the user’s authority to
operate the unit.
This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require
a safety connection to electrical earth.
Install two (2) “AAA” batteries in the
remote control. (Not included)
PRECAUTIONS:
• Replace both batteries at the same
time. Do not use a new battery with a
used battery.
• There’s a risk of explosion if a battery
is replaced by an incorrect type.
• Keep away from moisture.
• Be sure to match the
“+”
and
“–”
signs on the batteries with marks
inside the remote control.
• Please properly dispose of used up
batteries.
WARNING:
The batteries (or battery
pack) shall not be exposed to excessive
heat such as sunshine, fire or the like.
BATTERY INSTALLATION
3
1
7
5
The American Academy of Pediatrics dis-
courages media use by children younger
than two years. For more information,
visit www.aap.org.
SANYO television customers
should contact MRM
Recycling at 888-769-0149 or
visit their website at
w w w . m r m r e c y c l i n g . c o m
regarding SANYO’s waste
management plan.
ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection
Agency (EPA). ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and
the U.S. Department of Energy helping us all save money and protect the environment through
energy efficient products and practices.
Changes to default as-shipped television configuration and settings or enabling certain optional
features and functionalities will change the energy consumption of the television, this may
increase energy consumption beyond the limits required for ENERGY STAR qualification.
Wall mounting of the HDTV must be
performed by a skilled person.
For foot stand disassembly (if needed):
• Place HDTV face down on a padded or
cushioned flat surface to protect the
screen and finish.
• Remove the two (2) screws securing
each foot stand.
CAUTION:
Hold the
stands firmly as you remove screws.
1
Remove the four (4) M6x12 screws
threaded in the VESA holes on the
back of the TV.
2
Use the removed screws to secure
the TV to a wall mounting kit.
NOTE: Wall mounting kit is not included.
VESA standard interface: 200 x 200
M
ounting screws measurements:
Diameter: M6 (6mm) Length: 12mm
WALL
M
OUNTING
(OPTIONAL)
NOTE: Skip these steps if you are wall
mounting the TV.
1
Place HDTV face down on a
padded or cushioned flat surface
to protect the screen and finish.
2
Carefully insert both foot stands to
the bottom of the HDTV and
secure each one by inserting a
M4x30 screw on top, and the
longer M6x40 screw on the bottom
as indicated in the diagram below.
NOTE: Foot stand screws are found in
the literature package.
3
Position the HDTV on a firm and
flat surface with adequate space
for proper ventilation.
STAND ASSE
M
BLY
______
M4x30
M6x40
