manualshive.com logo in svg

SANY SY26U, Руководство по эксплуатации и обслуживанию


Поделиться
Скачать
background image

SY26U Excavator OMM

   Machine Controls

SANY                    

                    Operation and Maintenance Manual — 1119              

                                3-19

T

ABL

E OF 

CONT

E

N

TS

INTRODUCTION

SAFE

T

Y

MACHIN

E

CONTROLS

MACHINE 

OP

ERA

T

IO

N

MA

INTENANCE

SPEC

IFI

CA

TIO

N

S

OP

T

IO

N

A

L

 EQUI

PMENT

 

Hydraulic Lockout Control Lever

The hydraulic lockout control lever (1) disables or enables 
the controls for work equipment, swing, travel, and 
attachments (if equipped) to prevent accidental movement:

•

Pull the hydraulic lockout control lever to the 
locked (closed) (2) position to disable all hydraulic 
controls.

•

Push the hydraulic lockout control lever to the 
unlocked (open) (3) position to enable machine 
operation.

WARNING!

Always place the hydraulic lockout control lever in the locked (closed) position before leaving

 

the seat. Failure to follow this warning and unintended movement of the joysticks or travel 
control levers/pedals could result in death or serious injury.

NOTICE!

If any part of the machine moves when the hydraulic lockout control lever is in the locked

 

(closed) position, shut down the engine immediately. Contact a SANY dealer to solve this

 

problem.

Fig. 3-22

0003154

1

2

Fig. 3-23

0003155

3

Содержание SY26U









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SY26U

Kubota U17-3a Operating Instructions Manual preview
U17-3a
Бренд: Kubota Страницы: 118
Yanmar ACHILLES A18SE Owner'S Handbook Manual preview
ACHILLES A18SE
Бренд: Yanmar Страницы: 95
SANY SY135C Operation And Maintenance Manual preview
SY135C
Бренд: SANY Страницы: 278
Hyundai Robex 220LC-9A Service Manual preview
Robex 220LC-9A
Бренд: Hyundai Страницы: 41
GSI Group 100P36/100G36 Assembly Manual preview
100P36/100G36
Бренд: GSI Group Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды