Step 5: Attaching the Monitor Brackets to a television with recessed threaded inserts.
WARNING: DO NOT LAY THE TELEVISION FACE DOWN ON THE GLASS, lean it up against a wall or other solid surface!
Laying the television down on the glass may cause permanent damage.
The Monitor Brackets (b,c) should be placed as vertically close to center of the television as possible before installation. If your TV has
threaded inserts that are recessed and requires either a M4 or M5 diameter bolt, thread a M4 x 30 (e) or a M5 x 30 (g) Bolt through the
appropriate Lock Washer (l,m), an M4/M5 Washer (s), the Monitor Bracket, an M4/M5 Washer, a M4/M5 Spacer (p) and into the TV as
seen in Detailed View A of Diagram 5. If you determined that your TV requires a Bolt with a M6 or M8 Diameter, thread a M6 x 35 (i)
or a M8 x 40 (k) Bolt through the appropriate Lock Washer (n,o), the Monitor Bracket, a M6/M8 Spacer (q) and into the TV as seen in
Detailed View B of Diagram 5. Proceed to tighten the Bolts firmly with a phillips screw driver.
Detailed View A
Detailed View B
Diagram 5
b
c
e,g
i,k
l,m
n,o
s
s
q
p
Step 6: Attaching Monitor to Wall Plate and adding Safety Bolts
Warning: Some televisions may require 2 people to lift! Sanus is not responsible for personal injury or product damage.
First hook the Monitor Brackets (b,c) over the top of the Wall Plate (a), then let the bottom of the Monitor Brackets rotate in under
the bottom of the Wall Plate as shown in diagram 6a. Insert the Safety Bolts (v) into the threaded holes in the bottom of the Monitor
Brackets. Tighten them with the Allen Key (w) so that they sit behind the bottom tab on the Wall Plate as shown in the Detailed View of
Diagram 6b. Finally loosen the knobs and you are free to adjust your new flat panel TV.
Diagram 6a
Diagram 6b
Knob
b,c
v
a
Sanus Systems
2221 Hwy 36 West. St. Paul, MN 55113
800.359.5520 www.sanus.com 7.28.04
Sanus Systems
2221 Hwy 36 West. St. Paul, MN 55113
800.359.5520 www.sanus.com 7.28.04
Assembly Instructions for VMPL Flat Panel Wall Mount
Thank you for choosing a Sanus Systems Vision Mount Wall Mount. This product is designed to mount flat panel televisions weighing
up to 175 lb. to a vertical wall. It allows you to tilt your new television up to 15º without the use of tools.
Safety Warning:
If you do not understand these directions, or have any doubts about the safety of the installation, please call a quali-
fied contractor or contact Sanus at 800.359.5520 or www.sanus.com. We can quickly assist you with installation questions and missing
or damaged parts. Replacement parts for Sanus products purchased through authorized dealers will be shipped directly to you. Check
carefully to make sure there are no missing or defective parts. Never use defective parts. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specified by Sanus Systems. Sanus Systems can not be liable
for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use.
Note
: The supplied wall mounting hardware is not for steel stud walls or old cinder block walls. If you are uncertain about the nature of
your wall, consult an installation contractor. Sanus makes every effort to assure all necessary television mounting hardware is included.
If the hardware you need is not included please consult your local hardware store or call Sanus Systems.
Required Tools:
3/16 drill bit, 1/2” Masonry Bit for brick concrete or concrete block installations, wrench or socket, Phillips screw driver.
Supplied Parts:
(1) Wall Plate - a
(1) Left Monitor Bracket - b
(1) Right Monitor Bracket - c
(4) M4 x 12 Bolt - d
(4) M4 x 30 Bolt - e
(4) M5 x 12 Bolt - f
(4) M5 x 30 Bolt - g
(4) M6 x 12 Bolt - h
(4) M6 x 35 Bolt - i
(4) M8 x 16 Bolt - j
(4) M8 x 40 Bolt - k
(4) M4 Lock Washer - l (4) M5 Lock Washer - m
(4) M6 Lock Washer - n (4) M8 Lock Washer - o
(4) M4/M5 Spacer - p
(4) M6/M8 Spacer - q
(6) Lag Bolt Washer - r
(8) M4/M5 Washer - s
(6) Lag Bolt - t
(6) Conrete Anchor - u
(2) Safety Bolt - v
(1) Allen Key - w
Detailed View