S&T Kontron KBox E-410-APL Скачать руководство пользователя страница 62

Страница: 62 / 78

KBox E-410-APL - User Guide, Rev. 1.0

www.kontron.com

// 62

Figure 27: BIOS Advanced Menu - CPU Chipset Configuration

BIOS SETUP UTILITY

Main

Advanced

Power

Boot

Security

Save & Exit

CPU Chipset Configuration

EIST

[Enabled]

→

←

: Select Screen

Turbo Mode

[Enabled]

↑

↓

: Select Item

Active Processor Cores

[Disabled]

Enter: Select

Intel Virtualization Technology

[Enabled]

+/-: Change Opt.

VT-d

[Disabled]

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Feature

Option

Description

EIST

[Disabled], [Enabled]

Select whether to enable or disable Enhanced Intel SpeedStep
Technology.

Turbo Mode

[Disabled], [Enabled]

Select whether to enable or disable Turbo Mode.

Active Processor
Cores

[Disabled], [Enabled]

Select the number of cores to enable in each processor package.

Intel Virtualization
Technology

[Disabled], [Enabled]

Select whether to enable or disable Intel Virtualization
Technology.
A VMM can utilize the additional hardware capabilities provided
by Vanderpool Technology when selecting [Enabled].

VT-d

[Disabled], [Enabled]

Select whether to enable or disable CPU VT-d capability.

Содержание Kontron KBox E-410-APL















































































Результаты поиска

Содержание Kontron KBox E-410-APL

Отзывы:

S&T Kontron KBox E-410-APL, Руководство пользователя, Страница: 62 / 78

Результаты поиска

Содержание Kontron KBox E-410-APL

Отзывы: