manualshive.com logo in svg

S&T Kontron KBox E-410-APL, Руководство пользователя, Страница: 20 / 78

Поделиться
Скачать
S&T Kontron KBox E-410-APL Скачать руководство пользователя страница 20

KBox E-410-APL -  User Guide, Rev. 1.0 

 

www.kontron.com 

 

// 20 

 

4.1.

 

System Expansion Capabilities 

4.1.1.

 

System Expansion via SATA Interface 

The KBox E-410-APL comes with a 15+7-pin SATA power / data cable connector with the other end pre-connected to 
the onboard SATA data connector and drive power output wafer. Users can expand the system with a 2.5" SATA HDD / 
SSD drive. 

 

4.1.2.

 

System Expansion via mPCIe Card Interface 

The baseboard comes with an onboard mPCIe interface connector. The connector is intended to be used to install a 
full-sized mPCIe WLAN, Bluetooth or combo card. This socket may be unavailable in the ordered configuration with 
CAN Bus ports on the I/O panel. 

 

4.1.3.

 

System Expansion via M.2 Card Interface 

The baseboard comes with an onboard M.2 interface connector with Key B Type 2242 support. The connector is 
intended to be used to install an M.2 SSD card drive. 

 

 

 

If a customer requires WWAN functionality, it must be so stipulated when ordering, as 
an optional SIM card slot must be installed at the factory. 

WWAN modem adapter card (and SIM card) is able to be functional with the full-sized 
mPCIe interface connector or M.2 Key B interface connector. The WWAN signal can be 
selected to be connected to mPCIe or M.2 interface connector via the jumper JP1. 

 

 

Содержание Kontron KBox E-410-APL















































































Отзывы:

Нет отзывов