San Telequip SC10E4I Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 26

San Telequip SC10E4I Скачать руководство пользователя страница 22

San Telequip (P) Ltd.,
504 & 505 Deron Heights, Baner Road
Pune 411045, India
Phone : +91-20-65001587, 9764027070, 8390069393 Connecting. Converting. Leading!
email :

[email protected]

Service Mode

– UDP Client Mode

Compared to TCP communication, UDP is faster and more efficient. In UDP mode, you can

Uni-cast or Multi-cast data from the serial device server to host computers, and the serial
device can also receive data from one or multiple host

2.2.1.3 Management Accessible
IP Settings

Accessible IP Settings allow you to add or block the remote host IP addresses to prevent

unauthorized access. If host’s IP address is in the accessible IP table, then the host will
be allowed to access the SC10E4I. You can choose one of the following cases by setting
the parameter.

1.

Only one host with a special IP address can access the device server, “

IP

address

/255.255.255.255

” (e.g., “

192.168.0.1/255.255.255.255

”).

2.

Hosts on a specific subnet can access the device server. “

IP address/255.255.255.0

”

(e.g., “

192.168.0.2/255.255.255.0

”)

3.

Any host can access the device server. Disable this function by un-

checking the “

Enable

IP

Filter

” checkbox

«
...
20
21
22
23
24
...
»

Содержание SC10E4I



























Отзывы:

Нет отзывов