San Telequip SC10E4I Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 26

San Telequip SC10E4I Скачать руководство пользователя страница 17

San Telequip (P) Ltd.,
504 & 505 Deron Heights, Baner Road
Pune 411045, India
Phone : +91-20-65001587, 9764027070, 8390069393 Connecting. Converting. Leading!
email :

[email protected]

2.2.1.2 Port serial setting Serial
configuration

The following table describes the labels in this screen.

Label

Description

Port Alias

Remark the port to hint the connected device.

Interface

RS422 / RS485(2-wires) / RS485(4-wires)

Baud rate

110bps/300bps/1200bps/2400bps/4800bps/9600bps/19200bps/

38400bps/57600bps/115200bps/230400bps/460800bps

Data Bits

5, 6, 7, 8

Stop Bits

1, 2 (1.5)

Parity

No, Even, Odd, Mark, Space

Flow Control

No, XON/XOFF, RTS/CTS, DTR/DSR

Force TX Interval

Force TX interval time is to specify the timeout when no data has been

Time

transmitted. When the timeout is reached or TX buffer is full (4K

Bytes), the queued data will be sent. 0 means disable. Factory

default value is 0.

Performance

Throughput: This mode optimized for highest transmission speed.

Latency: This mode optimized for shortest response time.

Apply

Activate settings on this page.

«
...
15
16
17
18
19
...
»

Содержание SC10E4I



























Отзывы:

Нет отзывов