San Telequip SC10E4I Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 26

San Telequip SC10E4I Скачать руководство пользователя страница 16

San Telequip (P) Ltd.,
504 & 505 Deron Heights, Baner Road
Pune 411045, India
Phone : +91-20-65001587, 9764027070, 8390069393 Connecting. Converting. Leading!
email :

[email protected]

You must assign a valid IP address for SC10E4I before attached in your network environment.
Your network administrator should provide you with the IP address and related settings. The IP
address must be unique and within the network (otherwise, SC10E4I will not have a valid

connection to the network). You can choose from three possible “

IP configuration

” modes: Static,

DHCP/BOOTP. The Factory Default IP address is “

192.168.10.2

”

The following table describes the labels in this screen.

Label

Description

DHCP/BOOTP

Obtain the IP address automatically from DHCP server.

Static IP Address

Assigning an IP address manually.

Subnet Mask

Set the subnet mask to communicate on the network.

Gateway

Enter the IP address of the router in you network.

DNS Server

Enter the IP address of the DNS server to translate domain names

into IP address.

Switch Mode

Redundant:

When the connection between master-link and LAN fails, the

SC10E4I can automatically switch to another LAN port within10mS,

and still guarantees a non-stop connection

Switch:

Daisy Chain support to reduce usage of switch ports.

Authentication

You can set the password to prevent unauthorized access from network. Input the “

Old password

”

and “

New password

” to change the password. Factory default is no password.

«
...
14
15
16
17
18
...
»

Содержание SC10E4I



























Отзывы:

Нет отзывов