San Telequip SC10E4I Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 26

San Telequip SC10E4I Скачать руководство пользователя страница 10

San Telequip (P) Ltd.,
504 & 505 Deron Heights, Baner Road
Pune 411045, India
Phone : +91-20-65001587, 9764027070, 8390069393 Connecting. Converting. Leading!
email :

[email protected]

Ethernet to Serial

Delimiter:

You can define max. 4 delimiters (00~FF, Hex) for each way.

The data will be hold until the delimiters are received or the option

“

Flush Ethernet to Serial data buffer

” times out. 0 means

disable. Factory default is 0.

Flush Data Buffer After:

The received data will be queuing in the buffer until all the

delimiters are matched. When the buffer is full (4K Bytes) or after

"

flushE2S data buffer

" timeout the data will also be sent. You

can set the time from 0 to 65535 seconds.

Force TX Interval

Force TX interval time is to specify the timeout when no data has been

Time

transmitted. When the timeout

is reached or TX buffer is full (4K

Bytes), the queued data will be sent. 0 means disable. Factory

default value is 0.

Load Default

Remark the port to hint the connected device.

Service Mode

– Virtual COM Mode

In Virtual COM Mode, The driver establishes a transparent connection between host and serial
device by mapping the Port of the serial server serial port to local COM port on the host computer.
Virtual COM Mode also supports up to 5 simultaneous connections, so that multiple hosts can send
or receive data by the same serial device at the same time.

«
...
8
9
10
11
12
...
»

Содержание SC10E4I



























Отзывы:

Нет отзывов