background image

San Telequip (P) Ltd.,  
504, 505 Deron Heights, Baner Road, 
Pune 411 045, India. 

 

Phone: +91-20-65001587, 9764027070, 8390069393                      Connecting. Converting. Leading ! 
Email: 

[email protected]

                                                                                                                                  . 

 

Document Name : 

User Manual for GSM/GPRS modem 232/485. 

 
INTRODUCTION  

GSM/GPRS modem is a multi-functional, ready to use, rugged unit that can be embedded or plugged 
into  any  application.  The  modem  can  be  controlled  and  customized  to  various  levels  by  using  the 
standard AT commands. The modem is fully type-approved, it can speed up the operational time with 
full range of Voice, Data, Fax and Short Messages (Point to Point and Cell Broadcast). The modem 
also supports GPRS (Class 12) for spontaneous data transfer.  

 

Features 

 

 

Quad Band 850/ 900/ 1800/ 1900 MHz 

 

Output power 2W for GSM 850/ 900, 1W for GSM 1800 /1900 

 

Control via AT commands  (GSM 07.07 and 07.05) 

 

Interface-RS232 (DB9 female connector) or RS485 (3 pin screw type connector). 

 

Coding Scheme: CS1 to CS4 

 

CSD up to 14.4 kbps(Non-transparent) 

 

Mobile Originated (MO) and Mobile Terminated (MT),Cell Broadcast(CB),Text and PDU 
mode. 

 

Supports Internet service protocols TCP/UDP/FTP/HTTP/MMS 

 

Supports Packet Switched Broadcast Control Channel(PBCCH) 

 

Supports PAP protocol and USSD 

 

Supports auto-bauding for serial port from 4800 bps to 115200 bps. 

 

LED Indication for Power ON, Network status, Tx and Rx 

 

Dimensions: 93 x 78 x 33 mm ( excluding connectors) 

 

Weight: 125 grams 

 

Housing: Metallic Enclosure 

 

Installing the Modem 

To install the modem, plug the device on the provided SMPS Adapter.  

 

Inserting/ Removing the SIM Card  

To insert or remove  the SIM Card, it  is necessary  to  press the SIM holder ejector button with sharp 
edged object like a pen or a needle. When this is done the SIM holder comes out a little, then pull it 
out  and  insert  or  remove  the  SIM  Card.  Place  the  SIM  card  properly  as  per  the  direction  of  the 
installation.  It  is  very  important  that  the  SIM  is  placed  in  the  right  direction  for  its  proper  working 
condition.   

 

Connecting External Antenna  

Connect GSM/GPRS modem to the external SMA antenna male end. The frequency of the  antenna 
should  be  set  to  GSM850/900/1800/1900.  The  right  Antenna  should  be  used  with  the  specified 
frequency or else the antenna can damage the modem or it can affect the communication.  

 
Power Supply – 

Screw type connector with 9-30V DC, 2A supply. 

 

Modem connection to external devices:  
Connectors   

 

Connector 

Function 

SMA  

RF antenna connector  

 9 pin D-SUB / 3 pin screw type 

RS232 link / RS485 link 

Adaptor Socket  

Power supply connector  

SIM card holder  

SIM card   

 

Содержание 232











Отзывы: