A – In-Counter Napkin Dispenser
B – Mounting Adapter
C – Retainer Paddles
D – Thumbscrews (4 places)
E – Cover Release Buttons (2 sides)
Use to open dispenser face
Caution:
• Dispenser may experience product failure if not secured properly. • Do not use abrasive or caustic cleaners.
* If installing a dispenser into a stainless steel, marble, granite or other hard substrate, check with your local cabinet fabricator or cabinet maker regarding how to make the mounting hole cut-outs.
Product Reference Guide
The NSF listing is applicable only
to retro-fit applications where
the dispenser is mounted in an
enclosed counter or cabinet.
Requires the following tools:
Counter cutting tools may be required
if existing cutout needs to be enlarged.
Some tools may be required for the re-
moval of the old dispenser.
4. Open the cover by pressing the release
buttons found on each side of the
dispenser faceplate (E). Set dispenser to
the side.
5. Insert the mounting adapter (B) into
the hole making sure the retainer
paddles (C) are folded flat against the
mounting adapter.
6. Alternate turning the black thumb-
screws (D) clockwise until all four
retainer paddles (C) are firmly
engaged against the underside of the
counter.
Caution – Do not over tighten the
thumbscrews as this may cause permanent
damage to the mounting adapter.
1. Remove old dispenser and clean surface area using a damp cloth. For best fit the surface should be clean and flat.
2. Make sure there is proper clearance below the countertop for the dispenser housing.
3. If the existing cutout hole is smaller than the diagram above, then cut the hole larger to match the minimum sizes shown.
7. The black thumbscrews (D) must be
turned as shown above in order for
the dispenser to seat properly into the
mounting adapter. Refer to printed info/
icons on adapter flange.
8. Insert dispenser (A) into the opening
with cover open.
9. Secure the dispenser to the mounting
adapter by turning the thumbscrews
as shown above. Refer to printed info/
icons on adapter flange.
10. Load napkins properly and close the
cover. The napkin dispenser is ready
to use.
102165
B
C
A
B
D
E
VENUE™ IN-COUNTER NAPKIN DISPENSER WITH ADAPTER INSTALLATION INSTRUCTIONS
RETROFITTING H2003 & H2005 SERIES
This napkin dispenser will fit into
counter cutouts within this size range
5 3/8” (137mm) Min.
5 13/16” (148mm) Max.
7 7/16” (189mm) Min.
7 5/8” (194mm) Max.
Available In-Counter Napkin
Dispenser Configurations
Control Face =
Fullfold Napkin
Interfold Face =
Interfold Napkin
L OW
F O L D
M I N I
I N T E R
F O L D
TA L L
F O L D
M I N I F O L D
L OW
F O L D
M I N I
I N T E R
F O L D
TA L L
F O L D
M I N I F O L D
PLIÉE
PLEGADO
ENTREPLIÉE
INTERPLIEGUE
L OW
F O L D
M I N I
I N T E R
F O L D
TA L L
F O L D
M I N I F O L D
L OW
F O L D
M I N I
I N T E R
F O L D
TA L L
F O L D
M I N I F O L D
PLIÉE
PLEGADO
ENTREPLIÉE
INTERPLIEGUE
San Jamar • Chef Revival
555 Koopman Lane
Elkhorn, Wisconsin 53121
USA
T: +1.262.723.6133
F: +1.262.723.4204
www.sanjamar.com
www.chefrevival.com
www.sjcr.com
SJCR Canada
3300 Bloor Street West
CenterTower, 11th Floor
Suite 3140
Toronto, ON M8X 2X3
CANADA
T: +1 (262) 723.6133
F: +1 (262) 723.4204
Customer Care: (800) 248.9826
SJCR Europe
Schoorstraat 26a, bus 1
2220 Heist op-den Berg
BELGIUM
T: +32 1522 8140
F: +32 1522 8148
SJCR México
Av. Universidad #1377-701
Colonia Axotla CP 01030
Del. Alvaro Obregon
MEXICO, D.F.
T: +52 (55) 3626 0772
F: +52 (55) 5273 4495
