background image

 

Installation and Operation Manual 

55 

  5-8 Alarms 

Press and 

  then 

Alarms:

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
A warning message with beep sound is displayed when an alarm condition is met by user 
setting. Press 

 

to clear the alarm. However, the alarm will be displayed again when the 

alarm condition occurs again. The unit provides alarms for various functions. 

5-8-1 Fish                                                                     

Trigger an alarm when echo from the sensor 
is matched to preprogrammed fish profile.   
 

5-8-2 Deep                                                                 

Trigger an alarm when the depth value 
received from the sensor is deeper than a set 
value.   
 

5-8-3 Shallow                                                             

Trigger an alarm when the depth value 
received from the sensor is shallower than a 
set value.   
 

5-8-4 Temperature                                                 

Trigger an alarm when the reported 
temperature from the sensor is same as a set 
value.   
 

5-8-5 Temperature rate                                         

Trigger an alarm when the rate of 
temperature change from the sensor is same 
as a set value. 
 
 

5-8-6 Low battery                                                     

Trigger an alarm when battery voltage is 
lower than a set value.   
 

5-8-7 Navigation alarms                                       
Arrival radius : 

Trigger an alarm when your 

boat is approaching the destination to set 
value 

Anchor alarm : 

Trigger an alarm when your 

boat moves more than set valve 

XTE : 

Trigger an alarm when your boat 

moves off the current CDI scale.   

Danger : 

Trigger an alarm when your boat is 

getting closed to dangerous point.   
 

5-8-8 AIS                                                                     

See the Alarm option of 4-7 (AIS Settings). 
 

5-8-9 DGPS                                                                 

Trigger an alarm when DGPS signal is not 
received.   
 

5-8-10 Restore default                                           

Returns every alarm settings to default. 

 
 

 

Installation and Operation Manual 

56 

  5-9 Others 

Press and 

  then 

Others:

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

5-9-1 Simulate                                                           
simulation: 

Start/end exercise mode. 

mode: 

Refer to exercise mode of 4-2. 

speed:

 Simulated boat speed 

direction: 

Simulated course   

route: 

route to follow   

 

5-9-2 Waypoint                                                         

Select a way to display waypoints.   
 

5-9-3 GPS                                                                     

5-4 Refer to GPS setup. 
 

5-9-4 Units                                                                 

Select units of each number.   

Tip:

 

air pressure   

VHF receiver of the option, connected to 
barometer, is required: InHg or mB 
 

5-9-5 Comms                                                             

5-3 Refer to communication setup. 
 
.   

5-9-6 Time                                                                   
local time 

Change the sunrise & sunset time of chart in 
order to read correct time, provided from GPS 
satellite.     

time indication: 

Select time indicating form. 

date indication: 

Select date indicating form. 

 
5-9-7 Screen saver 

LCD screen will be off when you don

t press 

any front key pads within setting time, and 
while screen saver is on if you press any front 
key pads then LCD screen will be on again. 
 
 

5-9-8 Restore default                                             

It initializes all the set up information. 
 

5-9-9 Calendar                                                           

It provides calendar function. 

 

 

Содержание AIS-50N



































Отзывы: