Samsung WIP-500M Скачать руководство пользователя

Страница: 38 / 49

SOFT KEYS

Press the

[MENU]

button in idle mode, and then select the

[3. Soft Keys]

icon.

Station Message

You can send a reply by checking messages received from an extension on the
busy state.

•

Press the button to reuse the result.

•

Press the

[C/MUTE]

button to reset or the button to terminate.

World Clock

This function allows you to check current date and time in each region of the
world.

[MENU]

2. Utilities

[OK]

3. Calculator

[OK]

Enter Numbers

(Select Arithmetical

Operation Symbol)

Enter Numbers

[OK]

The result is

displayed.

When entering negative numbers,

press

# /

button.

When incorrect numbers are entered,

press the

[C/MUTE]

button.

[MENU]

2. Utilities

[OK]

4. World Clock

[OK]

(Move the Meridian Line)

The Corresponding Time of

Each Capital Name will be shown.

Move the meridian line to the city where you are located and press
the

[OK]

button. Time and date of other cities will be displayed

based on your location.

The sub menus of [Soft Keys] are decided by system.

[MENU]

3. Soft Keys

[OK]

1. Station MSG

[OK]

(Select a Station Number)

[OK]

1: Reply

Call is Connected.

To delete the message, select ‘2:
Delete’.

Home Page

Table of Contents

WIP-5000M Guide

Содержание WIP-500M


















































Результаты поиска

Содержание WIP-500M

Отзывы:

Похожие инструкции для WIP-500M

Бренды по названию

Популярные бренды

Samsung WIP-500M, Руководство пользователя

Результаты поиска

Содержание WIP-500M

Отзывы:

Похожие инструкции для WIP-500M

Бренды по названию

Популярные бренды