background image

BN68-05629A-00

QUICK START 

GUIDE

Welcome to your new Smart TV!

The following instructions cover assembling, connecting, and setting up your new TV. Make sure 

you have the accessories listed below.

Included in this box

Step 1

Installing the 
Wall Mount

Step 5

Power on and 
start the initial 
setup

Step 4

Using the 
Smart Touch 
Control

Step 3

Connect 
devices

Step 2

Connect 
Audio Devices

Step 1 

Installing the Wall Mount

Installation Precautions

 

Use the provided accessories and parts to install the wall mount.

 

Install the product onto a flat wall surface only.

 

Avoid the following areas to ensure the best product performance and prevent malfunctions:

 - Areas that are susceptible to vibration and impact: The TV might come loose from the mount 

and be damaged.

 - Next to fire sprinklers: Heat generated by the TV could activate the sprinkler.
 - Near high-voltage cables: Electronic interference from the high-voltage cables may disrupt 

the screen display.

 - Near a heating appliance: The product may overheat and malfunction.
 - Check the stability of the wall surface.
 - If the wall is too weak, reinforce it before installing the mount.

 

Do not remove a section of the wall and install the mount there.

 

Plug all the cables into the correct ports and connectors before installing the wall mount.

 

If attempting to install the product onto a non-concrete wall, consult an installation specialist 

first.

 

Once installed, the gap between the wall surface and the TV should be at least 31 mm.

 

For the types of walls the TV can be mounted on, check the model of your TV and then the 

corresponding installation guide on the back of the product. 

Wall Mount Accessories

 

Use only the provided accessories and parts to install the wall mount.

A (4) 

Mounting Piece

B (8) 

M4 X 8

C (4) 

M4 X 47

Wall Mount Brackets 

Left: 1, Right: 1

Length Adjustment 

Bars 

Ø25 : 2

D (24) 

M5 X 65

E (24) 

Anchor

F (2) 

M6 X 30

 

]

Check the type of the wall before installing.

Installation requirements for each wall type

 

Can only be mounted on a concrete or interior wall of sufficient thickness. Refer to the diagrams 

below.

 

NOTE

MDF = Medium Density 

Fiberboard
PW = Plywood

Min. 50 mm

Min. 10 mm

Min. 30 mm

Min. 30 mm

Min. 10 mm

Min. 10 mm

Art Wall

Art Wall

MDF or PW

MDF or PW

MDF or PW

Concrete

MDF or PW

Min. 

50 mm

Min. 

25 mm

Min. 

25 mm

With MDF 

or plywood 

reinforcement

MDF or PW 

(Excluding 

drywall thickness)

Composite 

Concrete Wall 

(Excluding 

drywall thickness)

 

Installation is not possible on a drywall or on a wall with no internal reinforcement.

0~24 mm

Art Wall

Drywall

No internal 

reinforcement

Cannot install directly on drywall.

MDF, PW, or Concrete

Also included: User manual, regulatory guide, IR extender, 

component adapter, RCA adapter x 2, power cord, Ferrite core

Smart Touch Control & 

 Batteries (AAA x 2)

3D Glasses Accessories:  

3D Active glasses, USB charge cable

1

1-1

1-2

TV

wall

1-1

1-2

TV

wall

Object

Object

31mm

1-1. 

If the wall is not flat, a gap may form 

after the installation is completed and 

this may result in a poor finish.

1-2. 

The TV cannot be mounted on the wall 

if there is an object between the TV and 

the wall that is 31 mm or thicker.

Check the wall’s type, thickness, and flatness.

2

L

R

Check the L and R markings on the front sides of the wall mount brackets.

F

3

Drive the level adjustment screw into the hole to get it prepared for use.

B

4

Attach the length adjustment bars to the two wall mount brackets using screws.

5

Place the assembly against the wall you wish to mount it on, and then mark the anchor insertion 

points on the wall.

6

E

 

]

Installation on drywall with studs.

15mm

D

Insert the anchors and screws where marked.

Requirements

 

Verify the location of the studs first and use wall screws.

 

Minimum Stud Size: 51x102mm or 2x4 in (Drill 3mm holes before inserting wall screws).

 

Drill the holes along the central axis of the stud.

 

Inserting the screws without pre-drilling the holes can split the stud.

 

]

The manufacturer will not be held liable for any issue arising from failure 
to comply with the instructions and requirements contained in this 
installation guide.

D

7

Remove the screws that hold the wall mount brackets in place.

One Connect Accessories:  

One connect, one connect cable

[UN85S9VF_QSG]BN68-05629A-00ENG.indb   2

2013-10-29   �� 1:25:40

Отзывы: