Samsung SVD-4600N, Руководство пользователя, Страница: 15 / 17

CO LO R CCD CA M ERA U ser G uide
28
CO LO R CCD CA M ERA U ser G uide
29
485 Control Board Connection Port RS-485 Control Port
$0//&$5*0/5&3.*/"- 539
$0//&$5*0/5&3.*/"- 539
1SFTTUIF'VODUJPO4FUVQTXJUDIJOUIF&9*5NFOVUPTBWFUIFDV SSFOUTFUUJOHTBOEFYJUUIF
M AIN SETUP m enu.
EXIT
-"/(6"(&:PVDBOTFMFDUUIFNFOVMBOHVBHFBDDPSEJOHUPZPVS
requirem ents.
3&4&53FTFUTUIFDBNFSBTFUUJOHTUPUIFGBDUPSZEFGBVMUT
3&563/4FMFDUUIJTUPTBWFUIF41&$*"-NFOVTFUUJOHTBOESFUVSOUPUIF ."*/4&561
m enu.
- CAM ID : Determ ines the cam era's identification num ber (betw een 0 and 255).
- BAUD RATE : You can select 2400/4800/9600/19200/38400/57600 bps.
- UART MODE : You can select NONE, EVEN or ODD for the parity bits.
- RET PKT : Determ ines w hether to send a com m and back to the controller device
w hen a com m unication control com m and is sent to the cam era.
- DISP CAM ID : Display cam era title on top left corner of the screen.
$0.."%+ $PNNVOJDBUJPO"EKVTUNFOU
This function sets up the cam era com m unication status w hen controlling the
cam era through an external control device.
8IFOUIF41&$*"-NFOVTDSFFOJTEJTQMBZFEQSFTTUIF'VODUJPO4FUVQ
TXJUDITPUIBUUIFBSSPXJOEJDBUFTA$0.."%+
Set up the m ode using the Function Setup sw itch.
*OJUJBMWBMVFPGDPNNVOJDBUJPOBEKVTUNFOU
O p era ting Y ou r Ca m era T rou b lesh ooting
ú
N othing appears on the screen.
Ķ
Check that the pow er cord and line connection betw een the cam era and m onitor are fixed properly.
Ķ
Check that you have properly connected VIDEO cable to the cam era VIDEO output jack.
ú
The image on the screen is dim.
Ķ Is lens stained w ith dirt? Clean your lens w ith soft, clean cloth.
Ķ
Set the m onitor to proper condition.
Ķ
If the cam era is exposed to too strong light, change the cam era position.
ú The image on the screen is dark.
Ķ
Adjust the contrast feature of the m onitor.
Ķ
If you have an interm ediate device, set the 75 Ω / Hi-z properly.
ú
5IFDBNFSBJTOPUXPSLJOHQSPQFSMZBOEUIFTVSGBDFPGUIFDBNFSBJTIPU
Ķ
Check that you have properly connected the cam era to an appropriate pow er source.
ú
The DAY/N IG HT menu does not work.
Ķ
Check that AGC of EXPOSURE SETUP m enu is ‘OFF’.
ú
The SEN S-UP function does not work.
Ķ Check that AGC of EXPOSURE SETUP m enu is ‘OFF’.
Ķ
Check that SHUTTER of EXPOSURE SETUP m enu is ‘A.FLK’ .
ú
The M otion D etection function does not work.
Ķ
Check that MOTION DEF of SPECIAL SETUP m enu is ‘OFF’.
ú Color is not correct.
Ķ Check the setting of W HITE BAL SETUP m enu .
ú The screen flickers continually.
Ķ Check that direction of cam era turns tow ard the Sun.
ú RS-485 communication fails.
Ķ Check the polarity betw een RS-485 Control Port and RS-485 cable.
Ķ
Check the RS-485 Com m unication establishm ent initial value
Ķ W e recom m end that you m ake ground connect betw een cam era and controller in order to m aintain
safety com m unication control.
Refer to the following table if you are experiencing trouble with your camera.
Contact an authorized technician if the table does not provide you with a
solution to the trouble.
34$PNNVOJDBUJPOFTUBCMJTINFOUJOJUJBMWBMVF
Item Cam era ID #"6%3"5& 6"35.0%& 1&51,5
Initial value 1 9600 /0/& &/"#-&
Item Cam era ID #"6%3"5& 6"35.0%& 3&51,5
Initial value 1 9600 /0/& &/"#-&