manualshive.com logo in svg

Samsung SNP-6201, Руководство пользователя, Страница: 20 / 162

Поделиться
Скачать
Samsung SNP-6201 Скачать руководство пользователя страница 20

20_

 installation & connection

installation & connection

 

Camera Wiring Interface Board

For the camera wiring, please refer to the picture below. 

 

J

 

Select Normal Open in the setup menu.

 

-

The sensor input is activated during a short for contact type, or when it is at “Low” level for 
the active type.

 

Select Normal Close from the Setup menu.

 

-

The sensor input is activated when open for the contact type or when in high impedance 
state (open collector) for the active type.

 

The maximum power capacity of the alarm outputs is DC +40V and  80 mA.

 

When connecting alarm input and output cables, be sure to connect one cable to each 
terminal respectively.

 

To connect products over the camera’s capacity, please use an additional relay device.

 

Connecting the power connector and GND incorrectly to the alarm out port may lead to fire 
and damage the camera.

AC-

FG

AC-

AUDIO OUT

AUDIO IN

GND

1.COM

1.NO

1.NC

IN1

IN2

GND

IN3

IN4

2.COM

2.NO

2.NC

D+

D-

TXD+

 TXD-

GND 

D+

D-

TXD+ TXD- GND

ETHERNET

Refer to Control Signal 

Connection Diagram

Audio 

IN

Video

Output 

Audio 

OUT

AC24V 2.5A

Power Input
Ground

Power Supply

Communications

Alarm output

Alarm 
Input

Alarm

Содержание SNP-6201



































































































































































Отзывы:

Нет отзывов