Samsung SNP-5321 Скачать руководство пользователя страница 32

Страница: 32 / 178

installation & connection

32_

installation & connection

notes for waterproofing

This product is an indoor unit. If it is installed outdoors, use the outdoor housing to make it

waterproof.

installing the unit on the wall by combining the outdoor housing and wall

mount

Install the wall mount on the vertical wall.

If the mount is installed on an inclined

wall, moisture can penetrate inside the

outdoor housing through the external

cable.

Wrap the screw part of the housing with

a sufficient amount of Teflon tape for

assembly.

When separating the dome cover and

fastening it to the housing frame, make

sure that the gasket is not loosened to

separate from the dome cover.

Install the wall mount adapter for

waterproofing, and apply the silicon

sealant between and around the wall and

wall mount for sealing.

Take particular caution to ensure that there

is proper sealing if the installed side is not

flat.

Wall mount

Silicon

sealant

Concrete wall

Screw

unit

Teflon tape

Dome gasket

Содержание SNP-5321



















































































































































































Результаты поиска

Содержание SNP-5321

Отзывы:

Samsung SNP-5321, Руководство пользователя, Страница: 32 / 178

Результаты поиска

Содержание SNP-5321

Отзывы: