Samsung SNP-5321 Скачать руководство пользователя страница 141

Страница: 141 / 178

English

_141

●

appen

DiX

appendix

Dip SwitcH SettinG

How to set up protocols and iD Dip Switches

You can control various settings of the camera system using the Communication and ID

DIP switches. Before installing the product, please set up the DIP switches according to the

installation environment.

Set the switches according to your installation environment. For more detailed setup

information, please refer to the chart on the next page.

The camera may malfunction if the switches are not fully turned On/Off; please

double check the switches before finishing setup.

Be cautious that the switch can be damaged when it is operated with a sharp tool.

Be cautious that the switch can be damaged when it is operated with an excessive

force.

AUDIO OUT

AUDIO IN

D+

D-

TXD+ TXD-

GND

1.COM

1.NO

1.NC

IN1

IN2

GND

IN3

IN4

2.COM

2.NO

2.NC

AC-

Communication Protocol DIP Switch (SW1)

Содержание SNP-5321



















































































































































































Результаты поиска

Содержание SNP-5321

Отзывы:

Samsung SNP-5321, Руководство пользователя, Страница: 141 / 178

Результаты поиска

Содержание SNP-5321

Отзывы: