Samsung SNP-5300 Скачать руководство пользователя страница 18

Страница: 18 / 134

18_

installation & connection

camera wiring interface Board

For the camera wiring, please refer to the picture below.

Select Normal Open in the setup menu.

The sensor input is activated during a short for contact type, or when it is at “Low” level for

the active type.

Select Normal Close from the Setup menu.

The sensor input is activated when open for the contact type or when in high impedance

state (open collector) for the active type.

The maximum power capacity of the alarm outputs is DC +40V and 80 mA.

When connecting alarm input and output cables, be sure to connect one cable to each

terminal respectively.

To connect products over the camera’s capacity, please use an additional relay device.

Connecting the power connector and GND incorrectly to the alarm out port may lead to fire

and damage the camera.

AUDIOOUT

-L

AUDIOIN

IN1

IN2

IN3

IN4

GND

OUT1

OUT2

Alarm

ETHERNET

Camera’s

internal

Sensor

input

Audio

OUT

AC24V 2.5A

Power Input

Ground

Power Supply

3.3V

Alarm Input

Sensor

GND

Содержание SNP-5300







































































































































Результаты поиска

Содержание SNP-5300

Отзывы:

Samsung SNP-5300, Руководство пользователя, Страница: 18 / 134

Результаты поиска

Содержание SNP-5300

Отзывы: