Samsung SNB-1001 Скачать руководство пользователя страница 33

Страница: 33 / 130

English

_33

●

aLL

ation & connection

Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT

port of the amplifier that the microphone is connected to.

Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker.

Check the specifications for audio input.

audio codec

G.711 PCM. μ-law 64kbps 8kHz sampling

full duplex audio

audio in

Used for mono signal line input (Max.2.4 Vpp)

audio out

Used for mono signal line output (Max.2.4 Vpp)

Line out impedance

600Ω

alarm input wiring Diagram

to connect to the alarm input port (SnB-1001)

Connect the alarm input signal to the input port in the rear panel.

ALARM IN : Used to connect the alarm input signal.

ALARM IN

GND

(5ma sink)

OUT

AUDIO

VIDEO

RESET

ALARM

ACT

LINK

NETWORK

DC12V

ALARM

Содержание SNB-1001



































































































































Результаты поиска

Содержание SNB-1001

Отзывы:

Samsung SNB-1001, Руководство пользователя, Страница: 33 / 130

Результаты поиска

Содержание SNB-1001

Отзывы: