manualshive.com logo in svg

Samsung SN6000 Series, Руководство пользователя

Поделиться
Скачать
Samsung SN6000 Series Скачать руководство пользователя страница 50

Samsung SN6000 Series User’s Manual

Using the Battery 39

Make it a practice to discharge your battery fully before
recharging the battery. This can help extend the life of the
battery.

Do not attempt to charge the battery in temperatures of under

41

o

F (5

o

C) or over 95

o

F (35

o

C

.)

Safely Using the AC Adapter and Batteries

Follow these guidelines to safely use the AC adapter and batteries:

Turn your equipment off and unplug the AC adapter if you
accidentally:

– Expose the equipment to liquid.

– Drop, jar, or damage the computer.

Use only Samsung-approved batteries, AC adapters and auto/
airline adapters.

Do not disassemble the battery, heat it above 122° F (50° C), or
burn it. The battery used in this computer may cause a fire or
chemical burn if mistreated.

Your computer's smart rechargeable battery may be considered
hazardous waste. If you replace your battery with a new one:

– Keep the old battery out of the reach of children.

– Dispose of the old battery promptly.

– Make sure that you follow all state and local

requirements when you dispose of the old battery.

Removing and Inserting the Battery

Your computer comes with the battery pack inserted. To remove the
battery pack:

1. Turn the computer’s power off.

2. Close the LCD panel and turn the computer over so that the

bottom of the unit faces up.

Содержание SN6000 Series

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды