manualshive.com logo in svg

Samsung SN6000 Series, Руководство пользователя

Поделиться
Скачать
Samsung SN6000 Series Скачать руководство пользователя страница 21

Samsung SN6000 Series User’s Manual

Using Your Computer for the First Time 10

“Boot Menu” on page 56 for information on disabling the logo screen).
After POST is successfully completed, the computer beeps once.

Screen messages are built into the computer to report both normal and
abnormal system conditions. If an error message appears, take any
action suggested in the message. If the message identifies the error
condition but does not suggest any corrective action, write down the
message and contact Samsung or an authorized Samsung service center
for assistance. (See “Troubleshooting”on page 87 for information on
contacting Samsung.)

Adjusting the LCD Display

You may wish to adjust the LCD display when you begin using your
computer. A TFT LCD does not require adjustment for contrast
because the contrast is set to remain at maximum.

To adjust the brightness of the LCD:

Press <Fn+Right Arrow> to increase the display brightness.

Press <Fn+Left Arrow> to decrease the display brightness.

Turning Off Your Computer

If your computer has a Windows operating system,
turn off your computer by performing the shutdown
procedure described in this section. Otherwise,
you may lose data.

To turn off the computer:

1. Click Start on the taskbar.

2. Click Shut Down.

3. Select the shut down option.

4. Click OK or Yes.

If the operating system is Windows 98, the computer turns
off.

Содержание SN6000 Series

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды