manualshive.com logo in svg

Samsung SID-562, Руководство пользователя, Страница: 6 / 17

Поделиться
Скачать
Samsung SID-562 Скачать руководство пользователя страница 6

COLOR DOME CAMERA

User Guide

10

COLOR DOME CAMERA

User Guide

11

•  The installation should be done by qualified service personnel or sysytem installers.
•  If the ceiling material is not strong enough to hold the installation screws, the 

camera may fall off. Reinforce the ceiling as needed.

Notes

Installation

 1) Separate the dome cover by counterclockwise rotation.
 2)   Separate the shield case by pulling from the camera  

body.

Latch

Locking direction

[Figure-1]

Unlocking direction
(Counterclockwise)

*   To install the dome cover on the camera body, turn the 

latches in locking direction as shown in the figure 1.

Locking direction
(Clockwise)

Main Body 
(Camera)

Shield Case

Dome cover

Overview

Installation

Installation

①

   Place the bracket provided on the installation 

surface and fix it with the M4 tapping screws 

(provided).

     (Select either 85X85 or 83.5X46)

②

   When placing the camera body on the plate, 

insert the plate pin into the mounting hole on 

the body as shown in figure-1 and fix it by 

turning clockwise.

③

   When placing the camera body on the plate, 

make sure the power and the BNC cables 

pass through their respective designated 

holes.(When placing the cable through its 

side,  thread  it  through  the  hole  at  the 

bottom.)

④

   After installation and adjustment of the 

camera are complete, secure the dome cover 

by turning it clockwise.

[Figure-1]

Locking 

direction

Plate pin

Unlocking direction

•  Please locate an arrow on bracket for installing direction that you wish to observe 

Area and then fix it with the M4 tapping screws.

Notes

Unlocking 

direction

M4 tapping 

 

screw (provided)

Dome cover

adapter plate

An arrow for installing directions

CAMERA

Locking 

direction

When installing on a adapter plate

❶ 

 Pan Base :

 control panning angle of camera

2 

 

 

Rotate Base :

 control rotating angle of camera

3 

 X3.6 Vari-focal Lens Module

4 

  Rotate Base Holding Screw : 

fix rotated position

5 

 

  

Pan Base Holding Screws (Color : Silver) : 

fix panned position

6 

 RS-485 Control Cable : 

The detailed description refers to p14

7 

 

  

Power Input Jack

 

8 

 Video Output Jack

9 

 

   

Function Setup switch :

   Display the menu on the screen and move the cursor to four directions to confirm 

status or after changing a selected item.

❿

 Video Output Terminal to Monitor

⓫

 Shield Case

 

⓬

 Dome Cover

Содержание SID-562


















Отзывы:

Нет отзывов