Samsung SCP-3120V Скачать руководство пользователя страница 3

4_

 

safety information

safety information

English 

English

 _ 5

SAFETY INFORMATION

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or 
electric shock.
If any unusual smells or smoke come from the unit, stop using the product. In such 
case, immediately disconnect the power source and contact the service center. 
Continued use in such a condition may cause fi re or electric shock.
If this product fails to operate normally, contact the nearest service center. Never 
disassemble or modify this product in any way. (SAMSUNG is not liable for problems 
caused by unauthorized modifi cations or attempted repair.)
  When cleaning, do not spray water directly onto parts of the product. Doing so may 

cause fi re or electric shock

  Do not expose the product to the direct airfl ow from an air conditioner.

Otherwise, it may cause moisture condensation inside the Clear Dome due to 
temperature difference between internal and external of the dome camera.

  If you install this product in a low-temp area such as inside a cold store, you must seal 

up the wiring pipe with silicon, so that the external air can not fl ow inside the housing.
Otherwise, external high, humid air may fl ow inside the housing, pooling moisture or 
vapor inside the product due to a difference between internal and external temperature. 

CAUTION

Do not drop objects on the product or apply strong blows to it. Keep away from a 
location subject to excessive vibration or magnetic interference.
Do not install in a location subject to high temperature (over 50°C), low temperature 
(below -10°F), or high humidity. Doing so may cause fi re or electric shock.
If you want to relocate the already installed product, be sure to turn off the power and 
then move or reinstall it.
Remove the power plug from the outlet when there is a lighting storm. Neglecting to do 
so may cause fi re or damage to the product.
Keep out of direct sunlight and heat radiation sources. It may cause fi re.
Install it in a place with good ventilation.
Avoid aiming the camera directly towards extremely bright objects such as sun, as this 
may damage the CCD image sensor.
Apparatus shall not be exposed to dripping or splashing and no objects fi lled with 
liquids, such as vases, shall be placed on the apparatus.
The Mains plug is used as a disconnect device and shall stay readily operable at any 
time.
  When using the camera outdoors, moisture may occur inside the camera due to 

temperature difference between indoors and outdoors. For this reason, it is 
recommended to install the camera indoors. For outdoor use, use the camera with 
built-in fan and heater.

7.

8.

9.

10.

11.

12.

1.

2.

3.

4.

5.
6.
7.

8.

9.

10.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions :

This device may not cause harmful interference, and

 This device must accept any interference received including interference that may 
cause undesired operation.

CAUTION

This equipment has been tested and found to comply with the limits for a Class A 
digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference when the equipment is operated in 
a commercial environment. 
This equipment generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instruction manual, may cause harmful 
interference to radio communications. Operation of this equipment in a residential area 
is likely to cause harmful interference in which case the user will be required to correct 
the interference at his own expense.

IC Compliance Notice

This Class A digital apparatus meets all requirements of the Canadian 
Interference.-Causing Equipment Regulations of ICES-003.

1)

2)

Correct disposal of batteries in this product

(Applicable in the European Union and other European countries with separate battery return systems.)

This marking on the battery, manual or packaging indicates that the batteries in this product should not be 
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols 
Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC 
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health 
or the environment.

To protect natural resources and to promote material reuse, please separate batteries from other types of waste 
and recycle them through your local, free battery return system.

Correct Disposal of This Product 

 (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories 
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their 
working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, 
please separate these items from other types of waste and recycle them responsibly to promote the sustainable 
reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government 
office, for details of where and how they can take these items for environmentally safe recycling.  

Business users should contact their supplier and check the terms and conditions of the purchase contract. 
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Содержание SCP-3120V




















































Отзывы: