setup screen
38_ setup screen
evenT SeTup
fTp / e-mail
You can configure the FTP/E-mail server settings so that you can transfer the images taken with camera to
your PC if an event occurs.
1.
From the Setup menu, select the <
event ( )
> tab.
2.
Click <
fTp / e-mail
>.
3.
Select <
fTp configuration
> or <
e-mail configuration
> and
enter / select a desired value.
•
FTP configuration
- Server address : Enter the IP address of the FTP server
that you transfer the alarm or event images to.
- ID : Enter the user ID with which you will log in to the
FTP server.
- Password : Enter the user account password for logging
into the FTP server.
- Upload directory : Specify the FTP path where you will
transfer the alarm or event images.
- Port : The default port of the FTP server is 21; however, you can use a different port number
according to the FTP server settings.
- Passive mode : Select <
on
> if you need to connect in passive mode due to the firewall or the FTP
server settings.
•
E-mail configuration
- Server address : Enter the SMTP address of the email server that you transfer the alarm or event
images to.
- Use authentication : Select whether to use authorization.
- Use SSL : Specify the use of SSL.
- ID : Enter the user ID for logging into the email server.
- Password : Enter the user account password for logging into the email server.
- Port : The default port of the email server is 25; however, you can use a different port number
according to the email server settings.
- Recipient : Enter the address of the email recipient.
- Sender : Enter the address of the email sender. If the sender address is incorrect, the email from the
sender may be classified as SPAM by the email server and thus may not be sent.
- Subject : Enter a subject for your email.
- Body : Provide the text for the massage. Attach the alarm or event images to the email that you are
preparing.
4.
When done, click [
Apply (
)
].
Storage
You can activate recording on your device, set the recording conditions, check the saved data capacity and
format the device itself.
1.
From the Setup menu, select the <
event ( )
> tab.
2.
Click <
Storage
>.
3.
Select a device to save data in.
M
`
If your device is properly recording data, it will display “
Recording
”.
`
If you see an “Error” message, check the following:
-
Check the storage to see if it is connected to the device.
-
Check the files in the storage to see if they are damaged.
-
Check the storage to see if they are physically damaged.
`
If the “Error” message does not disappear after following the
instructions, format the Micro SD card.
After formatting, if the error message still remains, replace the Micro
SD card.
`
If you remove the Micro SD card without changing a button to ‘off’
position in settings or if you connect a camera to an unstable power source, the Micro SD card may be damaged.
J
`
After operation in record mode, you are limited to 2 simultaneously accessible profiles, and to 3 connected users. However,
existing users will be sustained.
To make recording on the micro SD memory
1.
Set the SD card unit to <
on
>.
2.
Click the [
Apply (
)
] button.
3.
Check the memory card’s <
free size
> and <
Total size
>.
You can format the Micro SD card by clicking the <
format
> button.
`
Some frames may be skipped if the Micro SD memory card operates at the lower speed than recommended.
For more details, refer to “
Recommended Micro SD/SDHC/SDXC Memory Card Specifications
”. (Page 7)
`
For a Micro SD memory card with a large capacity, the formatting will be slowed down accordingly.
`
The data traffic will increase when the camera is set to higher resolution, higher bit rate, and/or higher framerate.
If there is too much data traffic, some frame may be skipped although it is stored in a full frame.
`
When a frame skip occurs, images are saved at the rate of min. one image per sec.
4.
Specify the storage action.
•
Record profile : Shows recording profile’s codec type.
•
Normal : Make recording at a certain frame rate.
•
Event : Set the recording type for a certain event that occurs.