Samsung OfficeServ 7200, Инструкция пользователя

Страница: 229 / 368

RECALL DIAL TONE
Press the NEW button to disconnect your existing call, wait for dial tone and then
make a new call on the same line.
NOTE: If this button does not appear on your keyset, the FLASH key may be pro-
grammed to recall dial tone.
SENDING A FLASH
While on an outside call, press the FLASH key to send a flash to the telephone
company. This is required for some custom calling features or CENTREX use.
NOTE: Flash is not available on an ISDN circuit.
BUSY LINE QUEUING WITH CALLBACK
If you receive a busy signal when you are selecting an outside line, this means that
the line or group of lines is busy.
• Press the CBK key, if programmed, or dial 44 . You will hear confirmation tone.
• When the line becomes free, the system will call you back.
• Lift the handset or press the ANS/RLS key to answer, wait for dial tone and dial
the telephone number or speed dial number again.
NOTES:
1.
A callback will be canceled if not answered within 30 seconds. If you have set
a callback, your
CBK key will light.
2. If the Hot Keypad feature has been turned off, you must first lift the handset
or press the
SPEAKER key before dialing.
CANCELING CALLBACK
A callback will be canceled if not answered within 30 seconds. If you have set a
callback, your
CBK key will light.
Your phone may have a maximum of five callbacks to lines and/or stations set at a
time. To cancel a callback:
• Press the CBK key, if programmed, or dial 44 . You will hear confirmation tone.
• While you are listening to confirmation tone, press the HOLD key. This will
cancel the oldest set callback.
NOTES:
1.
If the hot keypad feature is turned off, you must first lift the handset or press
the
SPEAKER key before dialing.
15 14
OUTSIDE CALLS
MAKING AN OUTSIDE CALL
• Lift the handset and press an idle outside line button, line group button or dial
a line access code to receive dial tone—
OR —press an idle outside line button,
line group button or dial a line access code to receive dial tone through the
speaker—
OR —press SPEAKER , receive intercom dial tone and dial a line
access code.
• Dial the telephone number.
• Finish the call by replacing the handset or pressing the ANS/RLS key.
NOTE: You will receive No More Calls tone when you attempt to make a call and
there is no key available for that line.
• If Least Cost Routing is enabled on your phone system, this button may be
labeled
LCR or accessed by dialing an access code (usually 9 ).
• If your system is programmed to require an authorization code before making
a call, dial
plus a valid code before selecting a C.O. line.
• If your system is programmed to require an account code before making a
call, press the
ACC button or dial 47 plus a valid bin number, press the ACC
button again, or , and then select a C.O. line. See Account Codes for more infor-
mation.
For more information on authorization and account codes, see your system
administrator.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the
SPEAKER key before dialing.
ANSWERING AN OUTSIDE CALL
• Lift the handset and you are automatically connected to the ringing call.
See Ring Preference under Customizing Your Keyset — OR —press the ANS/RLS
key to automatically answer on the speakerphone.
NOTE: If a call is flashing at your keyset but not ringing, you must press the flash-
ing button to answer.
UNIVERSAL ANSWER
Outside lines may be programmed to ring a general alerting device. To answer
calls ringing this device, dial
67 or press the UA key. This device can operate in any
one of the six different ring plans.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the
SPEAKER key before dialing.
Home Page iDCS Keyset Table of Contents