English 19
Gas r
ang
e
Adjusting low flame settings on cooktop burners
All Cooktop burner flames should be checked at their lowest setting. Use the
following steps to check and adjust the cooktop burner settings.
NOTE
Low setting adjustments should always be made with two or more burners
operating at the same time.
Flat-bladed screwdriver
Valve Stem
1.
Turn on two or more surface burners and
set them between MED and HI.
2.
Quickly turn one of the control knobs
counterclockwise to the lowest setting.
The flame should stay lit. if the flame
flutter or goes out, adjust the bypass
valve on the control valve for that
burner.
3.
Pull the control knob for that burner
straight off.
4.
Using a small flat-bladed screwdriver,
adjust the bypass valve screw in the base
of the valve stem. Turn the bypass valve
screw counter clockwise to increase the
flame size.
5.
Replace control knob and recheck the
low flame setting.
6.
Repeat step 1 thru 5 to check and adjust
the low flame settings on the remaining
surface burners.
Manual ignition
If there is a power failure, you can ignite the burner manually. Use caution when doing this.
1.
Hold a long gas grill lighter to the surface burner you want to light.
2.
Push in the control knob for that burner, and then turn it to the LITE position.
Turn on the grill lighter to ignite the burner.
3.
After the burner is lit, turn the control knob to adjust the flame level.
Flame level
The flames on the burners should always stay under the cookware, and should not
extend beyond the cookware bottom at any time.
WARNING
•
Flames larger than the cookware bottom may result in a fire or physical injury.
•
When you set a burner to simmer, do not turn the burner knob quickly. Watch
the flame to make sure it stays on.
•
After turning on a surface burner, check to make sure that the burner has
ignited. Adjust the level of the flame by turning the burner knob.
•
Always turn off the surface burner controls before removing cookware. All
surface burner controls should be turned OFF when you are not cooking.
•
Always turn the burners off before you go to sleep or go out.
•
If you smell gas, turn off the gas to the range and call a qualified service
technician. NEVER use an open flame to locate a leak.
NX7000K_VE_NX58M6850SS_AA_DG68-00909A-04_EN+MES+CFR.indb 19
2018-08-29 5:14:58
Содержание NX58M6850S Series
