Samsung ME16A4021AB Скачать руководство пользователя страница 16

Страница: 16 / 20

Step-by-step installation guide

D. MOUNT THE MICROWAVE

OVEN

FOR EASIER INSTALLATION AND PERSONAL

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle during

installation.

NOTE

: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE

: Filler blocks are required when mounting this

unit under any cabinet with a recessed bottom or

front overhang. (See page 9.)

IMPORTANT:The case damage that will occur

from over tightening screws when filler blocks

are not used is not covered under warranty.

NOTE

: When mounting the microwave oven, thread

power cord through hole in bottom of top cabinet.

Keep it tight throughout Steps 1–3. Do not pinch

cord or lift oven by pulling cord.

. Lift microwave, tilt it

forward, and hook slots

at back bottom edge

onto four lower tabs of

mounting plate.

. Rotate front of oven

up against cabinet

bottom.

. Insert a self-aligning screw through top center

cabinet hole. Temporarily secure the oven by

turning the screw at least

two full turns

after

the threads have engaged. (It will be completely

tightened later.)

Be sure to keep power cord

tight. Be careful not to pinch the cord,

especially when mounting flush to bottom

of cabinet.

B. ATTACH THE MOUNTING

PLATE TO THE WALL (CONT.)

To use toggle bolts:

Spacing for Toggles More

Than Wall Thickness

Bolt End

Mounting

Plate

Toggle

Bolt

Wall

Toggle Wings

. Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE

: Before tightening toggle bolts and wood

screw, make sure to coincide bottom line of the

Mounting plate with Horizontal line of “Rear wall

Template” and then the Mounting plate is properly

centered under the cabinet.

CAUTION

: Be careful to avoid pinching fingers

between the back of the mounting plate and the wall.

. Tighten all bolts. Pull the plate away from the wall

to help tighten the bolts.

C. USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws

and a hole large enough for the power cord to fit

through.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION

: Wear safety goggles when drilling holes

in the cabinet bottom.

SMH8165_XAA_DE68-03587A-10_EN.indd 16

6/19/2019 3:44:41 PM

Содержание ME16A4021AB





















Результаты поиска

Содержание ME16A4021AB

Отзывы:

Похожие инструкции для ME16A4021AB

Бренды по названию

Популярные бренды

Samsung ME16A4021AB, Руководство по установке

Результаты поиска

Содержание ME16A4021AB

Отзывы:

Похожие инструкции для ME16A4021AB

Бренды по названию

Популярные бренды