background image

4

1. Precaution

Follow these special safety precautions. Although the microwave oven is completely safe during ordinary use, 
repair work can be extremely hazardous due to possible exposure to microwave radiation, as well as potentially 
lethal high voltages and currents.

1-1 Safety precautions ( 

)

1. 

All repairs should be done in accordance with the 
procedures described in this manual. This product 
complies with Federal Performance Standard 21 
CFR

2. 

Microwave emission check should be performed to 
prior to servicing if the oven is operative.

3. 

If the oven operates with the door open :Instruct 
the user not to operate the oven and contact 
the manufacturer and the center for devices and 
radiological health immediately.

4. 

Notify the Central Service Center if the microwave 
leakage exceeds 5 mW/cm2.

5. 

Check all grounds.

6. 

Do not power the MWO from a “2-prong” AC cord. 
Be sure that all of the built-in protective devices are 
replaced. Restore any missing protective shields.

7. 

When reinstalling the chassis and its assemblies, 
be sure to restore all protective devices, including: 
nonmetallic control knobs and compartment covers.

8. 

Make sure that there are no cabinet openings 
through which people --particularly children--might 
insert objects and contact dangerous voltages. 
Examples: Lamp hole,ventilation slots.

9. 

Inform the manufacturer of any oven foundto have 
emission in excess of 5 mW/cm2 ,Make repairs to 
bring the unit into compliance at no cost to owner 
and try to determine cause. Instruct owner not to use 
oven until it has been brought into compliance.

 

CENTRAL SERVICE CENTER

10. 

Service technicians should remove their watches 
while repairing an MWO.

11. 

To avoid any possible radiation hazard,replace parts 
in accordance with the wiring diagram. Also, use 
only the exact replacements for the following parts: 
Primary and secondary interlock switches, interlock 
monitor switch.

12. 

If the fuse is blown by the Interlock Monitor Switch: 
Replace all of the following at the same time: 
Primary, door sensing switch and power relay, as 
well as the Interlock Monitor Switch. The correct 
adjustment of these switches is described elsewhere 
in this manual. Make sure that the fuse has the 
correct rating for the particular model being repaired.

13. 

Design Alteration Warning: Use exact replacement 

SDUWVRQO\LHRQO\WKRVHWKDWDUHVSHFL¿HGLQ

thedrawings and parts lists of this manual. This 
is especially important for the Interlock switches, 
described above. Never alter or add to the 
mechanical or electrical design of the MWO. 
Any design changes or additions will void the 
manufacturer’s warranty.  Always unplug the unit’s 
AC power cord from the AC power source before 
attempting to remove or reinstall any component or 
assembly.

14. 

Never defeat any of the B+ voltage interlocks. Do not 
apply AC power to the unit (or any of its assemblies) 
unless all solid-state heat sinks are correctly 
installed.

15. 

Some semiconductor (“solid state”) devices 
are easily damaged by static electricity. Such 
components are called Electrostatically Sensitive 
Devices (ESDs). Examples include integrated 

FLUFXLWVDQG¿HOGHIIHFWWUDQVLVWRUV,PPHGLDWHO\

before handling any semiconductor components or 
assemblies, drain the electrostatic charge from your 
body by touching a known earth ground.

16. 

Always connect a test instrument’s ground lead to 
the instrument chassis ground before connecting the 
positive lead; always remove the instrument’s ground 
lead last.

17. 

When checking the continuity of the witches or 
transformer, always make sure that the power is 
OFF, and one of the lead wires is disconnected.

18. 

Components that are critical for safety are indicated 
in the circuit diagram by shading,      or      .

19. 

Use replacement components that have the same 

UDWLQJVHVSHFLDOO\IRUÀDPHUHVLVWDQFHDQGGLHOHFWULF
VWUHQJWKVSHFL¿FDWLRQV$UHSODFHPHQWSDUWWKDWGRHV

not have the same safety characteristics as the 

RULJLQDOPLJKWFUHDWHVKRFN¿UHRURWKHUKD]DUGV

 NOTE 

: Connect the oven to a 20A. When 

connecting the oven to a 15A,make sure that circuit 
breaker can operate.

0*0$(065B%:LQGE

Содержание GE73MR










































Отзывы: