background image

Installation

Installation

English

20

 

Gas requirements

WARNING

•  Use only natural or LP (liquid propane) 

gases.

•  THE INSTALLATION MUST CONFORM 

WITH LOCAL CODES, OR IN THE 
ABSENCE OF LOCAL CODES, WITH 
THE NATIONAL FUEL GAS CODE ANSI/
Z223.1, LATEST REVISION (FOR THE 
UNITED STATES), OR WITH THE CAN /
CGA-B149 INSTALLATION CODES (FOR 
CANADA).

•  Gas dryers are equipped with a burner 

vent for use with natural gas. If you 
plan to use your dryer with LP (liquid 
propane) gas, it must be converted 
for safe and proper performance by a 
qualified service technician.

•  A 1/2” (1.27 cm) gas supply line is 

recommended and must be reduced to 
connect to the 3/8” (1 cm) gas line on 
your dryer. The National Fuel Gas Code 
requires that an accessible, approved 
manual gas shut-off valve be installed 
within 6” of your dryer.

•  Gas dryers installed in residential 

garages must be raised 18 inches (46 
cm) above the floor.

•  Additionally, a 1/8” (0.3 cm) N.P.T. 

(National Pipe Thread) plugged tapping, 
accessible for test gauge connection, 
must be installed immediately upstream 
of your dryer’s gas supply connection.

•  Your dryer must be disconnected from 

the gas supply pipe system during any 
pressure testing of the system.

•  Do not reuse old flexible metal gas 

lines. Flexible gas lines must be 
design certified by the American Gas 
Association (CGA in Canada).

NOTE

•  Your dryer uses an automatic ignition 

system to ignite the burner. There is no 
constant burning pilot.

•  Any pipe joint compound used must be 

resistant to the action of any liquefied 
petroleum gas.

•  As a courtesy, most local gas utilities 

will inspect a gas appliance installation.

Commonwealth of Massachusetts 
installation instructions

Your dryer must be installed by a licensed 
plumber or gas fitter. A “T” handle manual 
gas valve must be installed in the gas 
supply line to your dryer. If a flexible gas 
connector is used to install your dryer, the 
connector can be no longer than 3’ (36”).

WARNING

•  Gas leaks may occur in your system, 

creating a dangerous situation.

•  Gas leaks may not be detected by smell 

alone.

•  Gas suppliers recommend you purchase 

and install a UL-approved gas detector.

•  Install and use in accordance with the 

manufacturer’s instructions.

FlexDry_DM9600M-DC68-03381H_EN.indd   20

2017-01-29     10:47:33

Содержание FlexDry DVG55M9600V/A3-00











































































Отзывы: