background image

       

Disclaimer:  This information is provided “as is” without warranty of any kind

                          either expressed or implied, including, but not limited to, the implied
                          warranties of merchantability and fitness for a particular purpose.

REV 10-1

SUBJECT: CRT Substitution

BACKGROUND: When replacing a CRT for this model, the vendor CRT may be
                             substituted with either a Toshiba or Samsung.

SOLUTION: Parts must also be substituted in the heater and deflection circuits.
                    Substitute parts are listed in the parts list below according to the
                    CRT manufacturer.

PARTS LIST:

Location No.

15” Toshiba CRT

15” Samsung CRT

CRT

M36KUT23XX02

M36KUK35XX02

(CODE NO. : 897-250125AA)

(CODE NO. : 897-250134AA)

C447

CAP-MPPF, 400V, 304J

CAP-MPPF, 400V, 274J

(CODE NO. : 916-656300TJAX)

(CODE NO : 916-656270TJAX)

C442

CAP-MPPF, 400V, 274J

CAP-MPPF, 400V, 224J

(CODE NO. : 916-656270TJAX)

(CODE NO. : 01518-343-224)

R324

NONE

REF-CF, 1/2W, 5%, 470 ohm
(CODE NO. : 911-134707FF)

R639

REF-MO, 3W, 5%, 4.7 ohm

REF-MO, 3W, 5%, 1.6 ohm

(CODE NO. : 911-314707LF)

CODE NO. : 911-311507LFXA)

L404

COIL, H-LINEARITY, 6.7uH

COIL, H-LINEARITY, 4.2uH

(CODE NO. : 925-460187AB)

(CODE NO. : BH27-20003A)

D302

ZENOR DIODE UZ5.1V

ZENOR DIODE UZ5.6V

(CODE NO. : 893-290031AB)

(CODE NO. : 893-299004AE)

  SERVICE BULLETIN

 

PRODUCT: Computer Monitor

 BULLETIN: Monitor 95-002
 MODEL: CSR5987

Содержание CSR5987























Отзывы: