Samsung CLX-9251 Series Скачать руководство пользователя страница 396

Страница: 396 / 481

4. Troubleshooting

4.6.4. Horizontal periodic Light/Dark Band or Dot

A. Typical faulty images

B. Troubleshooting procedure

Step

Cause

Action

Horizontal periodic band (OPC, 94.2 mm)

•

OPC was exposed for a long time.

•

OPC is damaged by high voltage in a short time.

As some time passes, most of this trouble will disappear.

If not, replace the Drum Unit.

(Refer to 3.3.2.1.)

Horizontal periodic light/dark band (Roller-magnetic,
31.4mm)

•

Roller-magnetic is inferior in quality.

•

V-groove of Roller-magnetic surface is not
uniform.

Replace the Developer Unit.

(Refer to 3.2.2.2.)

4-211

Содержание CLX-9251 Series
























































































































































































































































































































































































































































































Результаты поиска

Содержание CLX-9251 Series

Отзывы:

Samsung CLX-9251 Series, Руководство по обслуживанию, Страница: 396 / 481

Результаты поиска

Содержание CLX-9251 Series

Отзывы: