Samsung CLX-9251 Series Скачать руководство пользователя страница 274

Страница: 274 / 481

4. Troubleshooting

4.5.2. Cx-xxxx type error code

► Error Code

C1–2110

► Error message

Prepare new yellow toner cartridge.

► Symptom

Yellow toner is almost empty.

► Troubleshooting method

1) Order new yellow toner cartridge because toner cartridge with level of “Low” will be exhausted soon.

► Error Code

C1–2120

C1–2130

C1–2140

► Error message

Replace with new yellow toner cartridge

End of life, Replace with new yellow toner cartridge

► Symptom

The yellow toner cartridge is at the end of its life.

► Troubleshooting method

1) Open the front cover.

2) Remove the yellow toner cartridge.

3) Install the new yellow toner cartridge (

CLT-Y809S

)

4) Close the front cover.

4-89

Содержание CLX-9251 Series
























































































































































































































































































































































































































































































Результаты поиска

Содержание CLX-9251 Series

Отзывы:

Samsung CLX-9251 Series, Руководство по обслуживанию, Страница: 274 / 481

Результаты поиска

Содержание CLX-9251 Series

Отзывы: