Samsung CE2733R Скачать руководство пользователя страница 15

Страница: 15 / 23

Samsung Electronics

6. Troubleshooting

6-1

PRECAUTION

1. CHECK GROUNDING BEFORE CHECKING FOR TROUBLE.
2. BE CAREFUL OF THE HIGH VOLTAGE CIRCUIT.
3. DISCHARGE THE HIGH VOLTAGE CAPACITOR.
4. WHEN CHECKING THE CONTINUITY OF THE SWITCHES OR TRANSFORMER, DISCONNECT ONE LEAD WIRE FROM THESE

PARTS AND THEN CHECK CONTINUITY WITHOUT THE POWER SOURCE ON. TO DO OTHERWISE MAY RESULT IN A FALSE
READING OR DAMAGE TO YOUR METER.

5. DO NOT TOUCH ANY PART OF THE CIRCUIT OR THE CONTROL CIRCUIT BOARD, SINCE STATIC DISCHARGE MAY DAMAGE IT.

ALWAYS TOUCH GROUND WHILE WORKING ON IT TO DISCHARGE ANY STATIC CHARGE BUILT UP.

6-1 Electrical Malfunction

SYMPTOM

CAUSE

CORRECTIONS

Oven is dead.

1. Open or loose lead wire harness

Check fan motor when thermal cutout is defective.

Fuse is OK.

2. Open thermal cutout (Magnetron)

No display and no operation at all.

3. Open low voltage transformer

Check Ass'y PCB when LVT is defective.

4. Defective Ass'y PCB

No display and no operation at all.

1. Shorted lead wire harness

Check adjustment of primary, interlock monitor,

Fuse is blown.

2. Defective primary latch switch (NOTE 1)

door sensing switch.

3. Defective monitor switch (NOTE1)
4. Shorted HVCapacitor
5. Shorted HVTransformer (NOTE2)

NOTE 1: All of these switches must be replaced at the same time.

(refer to adjustment instructions)
Check continuity of power relay contacts and if it has continuity, replace power
relay also.

NOTE 2: When HVTransformer is replaced, check diode and magnetron also.

Oven does not accept

1. Key input is not in-Sequence

Refer to operation procedure.

key input (Program)

2. Open or loose connection of membrane

key pad to Ass'y PCB

3. Shorted or open membrane panel
4. Defective Ass'y PCB

Replace PCB main.

1. Off-alignment of latch switches

Adjust door and latch switches.

2. Open or loose connection of high voltage

circuit especially magnetron filament
circuit

NOTE: Large contact resistance will bring
lower magnetron filament voltage and

Timer starts countdown but no

cause magnetron to lower output and/or

microwave oscillation.

intermittent oscillation.

(No heat while oven lamp and

3. Defective high voltage components

Check high voltage component according to

fan motor turn on.)

H.V.Transformer

component test procedure and replace if it is

H.V.Capacitor

defective.

H.V.Diode,H.V.Fuse
Magnetron

4. Open or loose wiring of power relay
5. Defective primary latch switch
6. Defective power relay or Ass'y PCB

Replace PCB main.

Содержание CE2733R
























Результаты поиска

Содержание CE2733R

Отзывы:

Похожие инструкции для CE2733R

Бренды по названию

Популярные бренды

Samsung CE2733R, Руководство по обслуживанию

Результаты поиска

Содержание CE2733R

Отзывы:

Похожие инструкции для CE2733R

Бренды по названию

Популярные бренды