Inner Body Parts
BIOMETRICS
OPEN
BIOMETRICS
OPEN
This section contains important information to ensure the user’s
safety and prevent potential damage to property. Please, read
this section carefully and use the product accordingly.
Warning
The product components used may vary depending on the installation
environment.
Outer Body
SHS-H705
www.samsungsds-nss.com/en
GC68-02067B ED:01
USER MANUAL
Convenient Opening
- User friendly access with
fingerprints and password
Graphic Interface
- Shows the operation status
of the doorlock
Double Authorization
- Requires fingerprint & password
combination to open
Double Locking
- Prevents opening from outside
(Do not disturb)
Built-in Fire Detection
- Generates alarm in case of a fire
Security Function
- Prevents intrusion from the outside
2
Safety Cautions
Product Components
• The user shall not install or repair the
product without authorization.
• Do not install the product in the place
where the gap between the door and the
frame is 5mm or more.
• Make sure that no unauthorized person
has the access to the password.
• Do not operate the product with wet
hands, and keep liquids such as water
or drinks away from the product, or
the product may malfunction or be
damaged.
• Do not use the excessive force or sharp
objects to push the lockbuttons, as this
can damage the product.
• Make sure that the door is completely
closed when going outside. The
manufacturer does not assume the
responsibility for any harm caused
by engagement of the lock on an
improperly closed door.
• Please do not hang on the product or
pull it.
• Be sure to correctly match the poles
(+/-) when installing the batteries. Install
the batteries with the correct poles (+/-).
• Long-term exposure to direct sunlight
may cause a crack on its touch pad.
Avoid exposure to direct sunlight during
installation.
• During battery replacement, use a new
one instead of the existing battery.
• Do not use water, benzene or alcohol
when cleaning the product, as these
fluids can cause product malfunction.
• Replace the batteries within 1 week
after the battery replacement alarm
sounds.
Inner Body
User Manual
‘AA’ Batteries (LR6)
Emergency Key (5EA)
Handle Shaft
Handle Shaft Spring
• Support Panel and Inner
Body Fastening Bolts
• Support Panel and Outer
Body Fastening Bolts
• Inner Fastening Bolts
• Strike Fastening Bolts
Number Pad Unlighted
Number Pad Lighted
Number Pad
Open Fingerprint
Cover Button
Fingerprint
Reading Panel
Outer Body Handle
Battery Cover
Auto/Manual
Locking Switch
CLOSE Button
Manual Open-
and close
Lever
Sound Control
Switch
Inner body
Handle
Registration
Button
Outer Body Parts
Mortise
Reset Button
Emergency
Keyhole
External Power
Port Cover
To setup door lock function, go to main menu.
Main Menu
While the door is open, open
up the battery cover from the
inside and press [Register]
button briefly.
When the light comes on,
on the number pad, enter
the master password
and press [
] button.
The pad is in the
main menu.
How to Change Master Password
Master password must be 4~12 digits long, and only one can be designated as
the master password.
●
Registered master password cannot be deleted, and can only be changed
with new password or Initialization of everything (master password, password,
fingerprints) and reregistration.
Note
1. Entering the main menu (refer to page 4)
2. Selecting change master
password menu
3. Entering new master password
When the light comes on, on the
number pad, press [1] and [
] button.
Enter the new master password
(4~12 digits) and press [
] button.
DING DONG
Success:
DING DONG DENG
Fail: DING-DONG x 2
1. Enter the main menu.
2. Press menu code, then press [
] button.
3. Select the function you want and press [
] button.
Summary of How to Select Modes
3
4
5
6
BIOMETRICS
OPEN
External Power Port
DING
DONG
DING
DONG
DENG
Strike
box
Mortise
(SHS-AML220)
Strike
Mortise
(SHS-AML320)
Strike
Or
Deadbolt
Latch bolt
Open-door sensor
SHS-AML320
SHS-AML220
When purchased, the product is set to Multi-leveled Security Code Entry Mode
initially. Please refer to “How to Set Up Multi-leveled Security Code Entry Mode”
for Common Mode setting.
Opening the Door from Outside with a Password
1. Multi-leveled Security Code Entry Mode
Touching [Number
Pad] will light up the
number pad.
When two arbitrary
buttons are lighted,
press the buttons in
order.
When the numbers on the
number pad are lighted,
enter the password and
press the [
] button.
Success: DING DONG
DENG DONG
Fail: DING-DONG x 2
●
Password must be entered after the light is on, and if does not, touch
[Number Pad] and re-enter.
●
To cancel, press [ ] button and re-enter.
●
If the password is wrong 5 times, “peep” warning alarm will sound 20 times
and the system will shut-down for about 3 minutes. When malfunction
happens, “beep” will sound every 10 seconds, and stop mode will be turned
off automatically after 3 minutes with multiple ‘beeps’.
Note
2. Common Mode
If the security mode is changed as ‘common mode’, second step will be skipped.
Use fingerprint to open the door from the outside. While the LED light is on,
place the finger with the registered fingerprint in the correct way.
Opening the Door from the Outside with a
Fingerprint
1. Pressing [Open Fingerprint
Cover] button
2. Reading Fingerprint
The cover for the
fingerprint reading panel
will open when [Open
Fingerprint Cover]
button is pressed.
When the LED light comes on, on [Fingerprint
Reading Panel], place fingerprint and wait for
about 1 second. When the door is unlocked,
fingerprint reading panel cover will close, and door
can be opened by pressing the handle downward.
Success:
DING DONG
DENG DONG
Fail:
DING-DONG x 2
BIOMETRICS
OPEN
OPEN
Pulling down the Door Lock Handle
Rotate the manual Open/Close lever
to the right or left to lock the door or
release the locking.
Rotating the Manual Open/Close
Lever to the Right or Left
Rotate the door lock handle of the inner
body downward.
Opening the Door from the Inside
Closing the Door from the Outside
Touch [Number Pad]
If you go outside while in manual locking mode,
touch [Number Pad] on the outer body.
Press [Open Fingerprint
Cover] button
If you go outside while in manual locking mode,
touch [Open Fingerprint Cover] on the outer body.
Press and hold the [Register]
button for 3 seconds.
When the number pad is lighted, enter
‘4560852580’ and then press the [
]
button.
- Success : DING DONG DENG
- Fail : DING-DONG x 2
Delete all data. When data is being Initialization, new master password will be
‘1234’ and previously registered fingerprints and password will be deleted.
Initialization (master password, password,
fingerprint)
DING DONG
→
DING DONG
1. Pressing the [Register] Button
(from the inside)
2. Entering the Numbers for
Initialization (from the outside)
Closing the Door from the Inside
Automatic
Locking Setting
The door is automatically locked
2 seconds after the door is closed.
Manual
Locking Setting
The door is locked when the [Close]
button is pressed.
Change master password
New master
password
Code
number (0~9)
Code
number (0~9)
New password
Read fingerprint
1
st
confirmation
2
nd
confirmation
Register password
Delete password individually
Delete all passwords
Register fingerprint
Delete fingerprint individually
Delete all fingerprints
Set Up double
authorization Mode
Turn off double
authorization Mode
Set Up Multi-leveled Security
Code Entry Mode
Turn off doubleSecurity mode
Read fingerprint
1
4
5
6
7
8
9
0
0
0
0
4
6
7
9
Main
menu
3
2
1
