background image

 

 

Guarantee 

We reserve the right to make any changes or improvements even 
after receipt of an order without being able to attribute a non-
compliance to the descriptions contained in the instruction manuals 
and selection guides. 
Our equipment is checked and tested in our workshops before 
shipment. 
To be valid, any complaint concerning a material will have to be 
formulated to us in writing within 10 days of the delivery. 
SAMES KREMLIN equipment, equipped with its original identification 
plates, has a one-year warranty or 1800H of operation (in the first term 
reaches) from the date of ex-factory against any defect of material 
or defect of it is up to us to see and appreciate. 
The warranty excludes wear parts, deterioration or wear resulting from 
abnormal or unscheduled use by SAMES KREMLIN, failure to observe 
instructions for proper operation or lack of maintenance. 
The warranty is limited to the repair or exchange of parts returned to 
our factory and recognized as defective by us and does not cover 
the listed wear parts.  
Any costs resulting from the operation cannot be charged to us. The 
costs of return to our workshops are the responsibility of the customer.  
An intervention can be carried out on site at the customer's request. 
In this case, the transportation and accommodation costs of the 
technician (s) will remain the responsibility of the applicant. 
Any changes made to our equipment without our consent will void 
the warranty.  
Our guarantee is limited to that of the suppliers of materials which 
enter in the composition of our sets. 

 

 
 

Содержание REXSON 2B124


























































Отзывы: