Salus SG888ZB, Системное руководство

Страница: 58 / 76

7 .3
Function
Parameters
Description
Default Value
d00 Select Units 0
0 SI Metric Units - °C
1 US Customary Units - °F
d01 Heating Control 0
0 Time Proportional & Integral (TPI)
1 ON/OFF – 0 .5°C (1 .0°F) Increments
2 ON/OFF – 1 .0°C (2 .0°F) increments
d02 Temp . Offset 0
-6ºF to +6ºF
(-3 .0ºC to +3 .0ºC )
Room Temperature Offset (1 .0°F/0 .5°C increments)
d03 Outdoor Sensor 0
0 Outdoor Sensor not connected to S1/S2
1 Outdoor Sensor or Ext . (d04) connected (10 kΩ)
3 Not Used
d04 External Sensor 0
0 d03 = 1, Ext . air sensor active, Int . sensor inactive
1 d03 = 1, Ext . floor sensor active, Int . sensor active
d05 Cooling Control 2
1 ON/OFF – 1 .0°F (0 .5°C) increments
2 ON/OFF – 2 .0°F (1 .0°C ) increments
d06 Actuator Type 1
0 NO Normally Open
1 NC Normally Closed
d07 Valve Protection 1
0 ARV10RFM Valve Exercise Disable
1 ARV10RFM Valve Exercise Enable
d08 Frost Setpoint 41ºF (5 .0ºC)
41ºF to 63ºF
(5 .0ºC -to 17ºC )
Minimum room temperature for frost protection and holiday mode
d09 Hour Format 1
0 12 Hour Time Format (eg . 5:00 pm)
1 24 Hour Time Format (eg . 17:00)
d10 Not Applicable N/A N/A This function is not applicable
d11 Daylight Savings 1
0 Daylight Savings Time (DST) Off
1 Daylight Savings Time (DST) On
d12
Max . Heat
Setpoint
95ºF (35ºC)
42ºF to 95ºF
(17 .5ºC to 35 .0ºC)
Maximum setpoint for heating mode
d13 Max . Cool Setpoint 41ºF (5ºC)
41ºF to 104ºF
(5 .0ºC to 40 .0ºC)
Maximum setpoint for cooling mode
d14
Floor Sensor High
Limit (heating)
81°F (27°C)
59ºF to 113ºF
(15 .0ºC to 45 .0ºC)
Disable heat demand when floor temperature is above high limit .
Increment: 1°F (0 .5°C)
d15
Floor Sensor Low
Limit (heating)
50°F (10°C)
43ºF to 104ºF
(6 .0ºC to 40 .0ºC)
Provide heat demand when floor temperature is below low limit .
Increment: 1°F (0 .5°C)
d16
Floor Sensor Low
Limit (cooling)
43°F (6°C)
43ºF to 113ºF
(6 .0ºC to 45 .0ºC)
Disable cooling demand when floor temperature is below low limit .
Increment: 1°F (0 .5°C)
d17 Preset Programs 1 0-1
Select program . Once selected, the selected program will overwrite
the present program .
d18
Heat/Cool Mode
Selection
0
0 Disable Heat/Cool selection
1 Enable Heat/Cool selection
Section 7
Setting Device Parameters
AS20WRF/BRF Thermostat – Functions & Parameters