Saluki SFS-3000 Series Скачать руководство пользователя страница 60

Страница: 60 / 65

Too thin

1) Discharging strength

not suitable.

2) Some discharge

parameters are not

suitable.

Adjust [splicing

discharging strength]

[discharging time] or

increase [overlap

amount].

Splicing line

Some discharge

parameters are not

suitable.

Adjust [splicing

discharging strength]

[discharging time] or

increase [overlap

amount].

Attention: when splice different types of fibers (different diameter) or multimode fiber,

sometimes there will be an upright line on the splicing point, we call it [splicing line], this

doesn’t influence the splicing quality (splicing loss and splicing strength).

10.2 Common error and solutions

When using fusion splicer, if there is error reminder, please refer to the following
solution. If problems still cannot be solved, then please contact the distributor for
help.

Содержание SFS-3000 Series


































































Результаты поиска

Содержание SFS-3000 Series

Отзывы:

Похожие инструкции для SFS-3000 Series

Бренды по названию

Популярные бренды

Saluki SFS-3000 Series, Руководство пользователя

Результаты поиска

Содержание SFS-3000 Series

Отзывы:

Похожие инструкции для SFS-3000 Series

Бренды по названию

Популярные бренды