IMPORTANT: IN THE INTEREST OF PRODUCT PERFORMANCE AND SAFETY PLEASE READ THESE INSTALLATION AND WARRANTY INSTRUCTIONS BEFORE INSTALLING THE PRODUCT.
MANTIS SMS806WF MULTIFUNCTION SENSOR electrical and installation specification effective 23/7/2022.
MUST BE INSTALLED
BY A LICENSED
ELECTRICIAN
DIY
Electrical class
Beam angle
Dimension (L x W x H mm)
Earth leakage current
Operating ambient min/max (°C)
Storage ambient limit (°C)
Operating humidity
Storage humidity
Calculated TM - 21, L
70
@ 85 °C (hrs)
70
@ 85 °C (hrs)
Reported TM - 21,L
Aiming restrictions (if any)
Product application
IK rating (if relevant)
Product installation orientation
CCT (k) switch control (TC)
Dimmable
Insulation cover rating (if any)
PIXIE connectivity
N/A
Replaceable LED
N/A
IP rating
Attachment type
User replaceable LED
IP rating for interior products: The designated IP rating is “from below the ceiling” unless otherwise specified.
IP rating ALL products; Termination of the product must be made in accordance with the IP rating.
Earth Leakage current: Is calculated in accordance with AS/NZS 60598.1:2017.
No
N/A
IP66
N/A
10% to 85% RH, NC
N/A
N/A
0 to 60
10% to 85% RH, NC
N/A
Class II
N/A
N/A
N/A
0 to 40
140 x 115 x 75
Refer dimension detail
N/A
Interior & exterior residential & commercial spaces
Ceiling or wall mount
SAL National Pty Ltd. 40 Biloela Street Villawood NSW 2163 ABN 21 633 189 474
Copyright SAL V12 FEB 2020 |
www.sal.net.au
| Page 1 of 3
SAL products are designed in accordance with all mandatory International and Australian Standards, which require installation
in accordance with AS/NZS3000 by a qualified installer and regular cleaning and maintenance of the equipment. Products are
sold in accordance with the following instructions and SAL standard terms and conditions of sale, available via www.sal.net.au.
SMS806WF
SMS806WF/BK
Model No.
Power (W)
Input
(V)/(Hz)
Working
Humidity (RH)
Detection
Angle
Detection
Motion Speed
Detection
Distance (m)
Time
Setting
Light
Control (lux)
Sensor
Mass
(N.W.g)
Body
Colour
Type
0~93%
110°
0.6~1.5
(m/s)
10~2000
10s ~ 30min
PIR
or
PE
220
Grey
Black
Max. 18m at
installation heights
1.8m-2.5m
220-240/50
Due to continued product and information updates, product data sourced from sal.net.au shall not form part of any contract and or technical performance
guarantee unless expressly confirmed in writing by SAL at the time of order.
General product application requirements (if applicable) :
1. CCT or POWER selections (where supplied) – IMPORTANT, where CCT colour temperature or POWER selection switching is provided, it is important to switch OFF the
power before the selection is made, otherwise equipment damage may occur.
2. Recycling – SAL encourages recycling, please consider the environment when disposing of packaging, batteries & components.
3. Switching or test intervals – For optimum product performance, good design practice does not encourage 24/7 operation of lighting products without the provision
of a routine switching or regulatory test cycle. As a guide for continual operation installations, a twelve (12) hour duration for Industrial and Commercial applications
and a six (6) hour duration for Residential applications should be considered.
4. Product maintenance – In line with the relevant design standards and to protect your investment, it is important to have in place a routine cleaning program that
reflects the installation environment and maintains the product in a clean and functional condition.
IMPORTANT - The supply must be isolated before any product maintenance or cleaning is conducted. In addition, damage to ANY cable or cord supplied with the
product must be addressed as follows; For attachment type X having a specially prepared cable, if the external flexible cable is damaged, it must be replaced by an
equivalent cable exclusively available from the manufacturer or authorised installer. For attachment type Y, if the external flexible cable is damaged, it must be
exclusively replaced by an equivalent cable by the manufacturer or authorised installer. For attachment type Z, if the external flexible cable is damaged, the cable
cannot be replaced and the luminaire must be destroyed.
5. Adverse, corrosive and coastal installation environments – Unless the product is specifically designated for such applications in these installation instructions, which is
supported by a professional maintenance program; installation of equipment in such environments is not recommended.
6. Dimming products – Dimming circuits and product compatibility must be validated by the installer before installation; SAL cannot be responsible for third party
changes in dimmer compatibility.
7. Suspended products – For installation safety, any suspended products must NOT be installed in high air movement spaces or locations subject to impact.
8. Light source replacements – (Non-replaceable light sources) - The light source of the product is deemed not replaceable, when the product reaches its end of life,
the complete product must be replaced by a qualified installer. (Non-user replaceable light sources) - The light source of the product must only be replaced by the
manufacturer or qualified installer. Caution, risk of electric shock.
9. Interior downlights and sensors with remote drivers and electrical accessories – The mounting facilities provided for the device (if any), need only be utilized if in the
application of the product is required by AS/NZS3000. Drivers are not designed for installation environments that restrict conventional airflow.
10. Ripple injection, induced flicker (QLD & NSW regions) – Installations subject to off-peak ripple induced flicker, (which are beyond the manufactures control), should
strongly consider the use of circuit filtering products, or for interior downlight installations, the use of products designed to block the signal interferences, such as the
SAL SFI series.
11. Floodlight products – Unless nominated aiming restrictions or installation parameters apply, products are designed for installation environments between ground and
15 metres in height, subject to the desired optical performance being achieved. For floodlight installation environments that have restricted access (eg: columns and
roof-lines) which are subject to unstable electrical supply or electrical surges (which void warranty), consideration of the installation of an independent surge protector
is strongly recommended.
12. Emergency enabled products – In the interest of transport and safety, emergency products are supplied with the battery disconnected. In addition to specific
emergency commissioning instructions, this battery MUST be connected at the time of installation. Continual use in emergency mode greater than 240 hours without
recharge, will result in battery failure and void battery warranty.
Max. 500
Max. 1000
Max. 2000
(Idle 1W)
