IMPORTANT: IN THE INTEREST OF PRODUCT PERFORMANCE AND SAFETY PLEASE READ THESE INSTALLATION AND WARRANTY INSTRUCTIONS BEFORE INSTALLING THE PRODUCT.
SAL National Pty Ltd. 40 Biloela Street Villawood NSW 2163 ABN 21 633 189 474
Copyright SAL V5 JUN19 |
www.sal.net.au
| Page 1 of 2
SAL products are designed in accordance with all mandatory International and Australian Standards, which require installation
following instructions and SAL standard terms and conditions of sale, which are available via www.sal.net.au.
by a qualified installer and regular cleaning and maintenance of the equipment. Products are sold in accordance with the
Nominal frequency (Hz)
Product installation orientation
Operating ambient min/max (°C)
Product application
Operating humidity
Pixie connectivity
Storage ambient limit (°C)
*IP rating
Storage humidity
Attachment type
Horizontal wall mount or desktop
50
*IP rating for interior products: The designated IP rating is “from below the ceiling” unless otherwise specified.
*IP rating ALL products: Termination of the product must be made in accordance with the IP rating.
Model No.
Input
Min / Max loads
Colour
Dimension L x W x H (mm)
PIXIE SGW/BT GATEWAY product electrical and installation specification effective 4/07/2019.
MUST BE INSTALLED
BY A LICENSED
ELECTRICIAN
DIY
0 to 40
Interior residential or commercial
10% to 85% RH, NC
0 to 40
20
N/A
10% to 85% RH, NC
Yes
Dimming Technique
Wireless
N/A
Bluetooth Mesh Technology
General product application requirements (where applicable) :
2. Recycling – SAL encourages recycling, please consider the environment when disposing of packaging, batteries & components.
3. Switching or test intervals – For optimum product performance, good design practice does not encourage 24/7 operation of lighting products without the provision of
a routine switching or regulatory test cycle. As a guide for continual operation installations, a twelve (12) hour duration for Industrial and Commercial applications and six
(6) hour duration for Residential applications should be considered.
4. Product maintenance – In line with the relevant design standards and to protect your investment, it is important to have in place a routine cleaning program that
reflects the installation environment and maintains the product in a clean and functional condition.
5. Adverse, corrosive and coastal installation applications Unless the product is specifically designated for such applications in these installation instructions, which is
supported by a professional maintenance program; installation of equipment in such environments is not recommended.
6. Dimming products – Dimming circuits and product compatibility must be validated by the installer before installation; SAL cannot be responsible for third party
changes in dimmer compatibility.
IMPORTANT - The supply must be isolated before any product maintenance or cleaning is conducted. In addition, damage to ANY cable or cord supplied with the
product must be addressed as follows; For attachment type X having a specially prepared cable, if the external flexible cable is damaged, it must be replaced by an
equivalent cable exclusively available from the manufacturer or authorised installer. For attachment type Y, if the external flexible cable is damaged, it must be
exclusively replaced by an equivalent cable by the manufacturer or authorised installer. For attachment type Z, if the external flexible cable is damaged, the cable
cannot be replaced and the luminaire must be destroyed.
1. CCT or POWER selection (where supplied) – IMPORTANT, where CCT or POWER selection switching is provided, it is important to switch OFF the SUPPLY before the CCT
selection is made, otherwise equipment damage may occur.
10. Floodlight products – Unless nominated aiming restrictions or installation parameters apply, products are designed for installation environments between ground and
15 metres in height, subject to the desired optical performance being achieved.
7. Suspended products – For installation safety, any suspended products must NOT be installed in high air movement spaces or locations subject to impact.
9. Interior downlights and sensors with remote drivers – The mounting facilities provided for the transformer/driver (if any), need only be utilized if in the application of the
product is required by AS3000. Drivers are not designed for installation environments that restrict conventional airflow.
8. Light source replacements – (non-replaceable light sources) - The light source of the product is deemed not replaceable, when the product reaches its end of life,
Caution, risk of electric shock.
manufacturer or qualified installer.
the complete product must be replaced by a qualified installer. (Non-user replaceable light sources) - The light source of the product must only be replaced by the
SGW/BT
5V DC - 1A
N/A
Matt Black
95 x 95 x 24
