Saia Burgess Controls PCD7.D412DTPF Скачать руководство пользователя страница 28

Страница: 28 / 73

Saia-Burgess Controls AG

Manual PCD7.D412DTPF & PCD7.D4xxxT5F │ Document 27-620 – Release ENG07 │ 2019-06-20

3-16

Logic Controller

LED and operating status (12" pWeb panel, only)

3.5

LED and operating status (12" pWeb panel, only)

The CPU is capable of the operating statuses listed in the following table. On the

12" pWeb panel, the status is indicated by a multicoloured LED. On the other pan

els, the status can be shown on the display.

Status

Description

LED

No power

No power connected

aus

Run

Normal processing of the user program

after startup

green

Run (conditional)

Conditional Run status A condition has

been set in the debugger (Run until...),

which has not yet been fulfilled

green…green…green

Run with error

The same as Run, but with an error mes

sage

green

Run (conditional) with

error

The same as Run (conditional), but with an

error message

green…green…green

Stop

The status Stop occurs in the following

cases:

■ Downloading with the option “Remain in

Stop status”

■

PGU stopped by programming unit

red

Stop with error

The same as Stop, but with an error mes

sage

red

Halt

The status Halt occurs in the following

cases:

■ Halt instruction processed;

■ Serious error in the user program;

■ Hardware fault;

■ No program loaded;

■ No communications mode on the S-Bus

PGU or Gateway Master Port.

red

System diagnostics Description

LED

Battery fault in Run

Flashes at interval of 500 ms

orange green orange green

Battery fault in Run

conditional

red green red green

Battery fault in stop /

halt

red…red…red

No SD memory card

red blue green red blue green

SD memory card but

no firmware

red green blue red green blue

Содержание PCD7.D412DTPF










































































Результаты поиска

Содержание PCD7.D412DTPF

Отзывы:

Saia Burgess Controls PCD7.D412DTPF, Руководство пользователя, Страница: 28 / 73

Результаты поиска

Содержание PCD7.D412DTPF

Отзывы: