Important Information about
The Sagemcom FAST 5295 (SAX2V1S)
1
INSTALLATION AND SAFE USAGE INSTRUCTIONS
1. Place the router in a vertical orientation on a flat surface.
2. Connect the manufacturer supplied AC to DC power adapter. The FAST 5295 router
requires the use of a 12VDC, 3A power adapter. Only use a manufacturer supplied
and approved power adapter and Ethernet cable.
3. Connect the “FAST 5295” to the AC Mains in accordance with the installation instructions in this booklet, and the
markings on the identification label (voltage, current, and frequency of electricity network).
4. Connect the Ethernet cable (provided) to the RJ45 port labeled “internet” on one end and to the Internet access device
provided by your ISP on the other end.
5. According to installation method required by our ISP:
-
Connect the Ethernet cable (provided) to the RJ45 port labeled “Internet” on one end and to the Internet access
device provided by your ISP on the other end.
-
For connection of a computer with an Ethernet cable use one of the RJ45 ports on the product marked “Ethernet”,
"1", "2", "3". Then connect the other end of the Ethernet Cable to the Ethernet port of a computer. Repeat as
necessary with the other available Ethernet ports.
The product label (with manufacturer identification, model identification) is located on the product bottom.
When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and
injury to persons including the following:
1. Do not use this product near water and avoid contact with moisture. For example, does not use near a bathtub, wash
bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Care should be taken so that liquids are not
spilled on this equipment.
2. This equipment is for indoor use only, do not place or install in an outdoor location.
3. Ethernet ports are intended to be connected to indoor cable circuits that are exclusively located within the building where
the product FAST 5295 is installed, and don’t terminate on a remote equipment earthed to a different earthing network.
4. The devices connected to the telephone interfaces must be kept indoor use only.
Caution: To reduce risk of electric shock, fire or damage to the equipment, do not connect
telephone or telecommunications public network into “PHONE” port.
5. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric
shock from lightning.
6. Do not use the telephone to report a gas leak in the vicinity of the leak.
7. Make sure the power socket to which you connect the power cord is easily accessible and as close as possible to the
equipment so that the appliance can be unplugged quickly in case of a problem.
8. Place your product on a firm, solid surface, no obstacle at a minimum distance of 51cm (1.67 feet). If you put it on
something unsteady, it may fall and be damaged. If you place it on a soft surface, such as rug, sofa or cushion, the vents
may be blocked, causing the product to overheat.
9. Never insert objects into the vents of this equipment as this can result in the risk of electrical shock or fire.
10. As the power adapter is the only way to connect to the electrical network, the product must be installed near an easily
accessed power outlet.
11. This equipment should only be operated with the type of power supply (Voltage and Current) indicated on the marking
label.
12. Do not overload wall outlets or extension cords. Doing so can result in the risk of fire or electrical shock.
13. Avoid blocking any vent openings or exhaust exits on this equipment. Do not place equipment in a built-in installation
such as a cabinet that may impede the flow of air through the ventilation openings.
14. The equipment should be situated away from heat sources such as radiators, heat registers, stoves, or other heat
producing appliances and equipment.
15. To disconnect this equipment from AC power, unplug the power supply from the AC wall socket.
16. Care should be taken to ensure that the power cord is routed, so it is not likely to be walked on or pinched by items
placed upon or next to it.
17. Unplug this equipment before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning
only.
18. This equipment is not user serviceable and is to be serviced by qualified personnel only. Do not disassemble this
equipment. If service is required, disconnect all power from the equipment and consult qualified service personnel.
19. To disconnect this equipment from AC power, unplug the power supply from the AC wall socket.
20. Use the product in the environment specified as below:
-
Air temperature between 0°C (32 F) and +40°C (104 F).
-
Relative humidity between 5% and 95%.
-
Altitude: 4000 meters (13000ft) maximum.
