background image

5

I M P O R TA N T   S A F E T Y   I N F O R M AT I O N

Basic safety precautions should be observed when operating the WPC-2 product and other associated 

equipment.

1. A qualified electrician must install the WPC-2 in accordance to the National and Local Electrical Codes.
2. The WPC-2 must not be less than 5 feet (3 meters in Canada) from inside edge of pool.  ONLY USE 

COPPER CONDUCTORS.

3. Do not exceed the maximum ratings of individual components, wiring devices, and current carrying 

capacity of conductors.

4. For the bonding, grounding, installing, and wiring of underwater lights to the WPC-2, refer to Article 

680 of the National Electrical Code or Article 68 of the Canadian Electrical Code.

5. This device should never operate equipment that could cause property damage, bodily injury, or death 

should it be activated unexpectedly.

6. Never allow children to operate the WPC-2 unsupervised.

F C C   W A R N I N G

1.  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any 

interference received, including interference that may cause undesired operation.

2.  Changes or modifications not expressly approved by S.R Smith. could void the user’s authority to 

operate the equipment.

WARNING

• 

TURN OFF INCOMING POWER BEFORE SERVICING EQUIPMENT. 

• 

ALL INSTALLATION AND MAINTENANCE WORK MUST BE PERFORMED BY QUALIFIED ELECTRICAL 

PERSONNEL ONLY.

• 

VERIFY ALL ELECTRICAL RATINGS BEFORE INSTALLATION IS COMPLETE.

LOCATION

Install the WPC-2 enclosure using the mounting plates included with each enclosure.  

 

The WPC-2 is housed in a Type 3R rainproof enclosure and can be mounted anywhere between 

 

the pool equipment and the breaker panel.

ELECTRICAL SHOCK HAZARD – SWITCH DOES NOT TURN OFF INPUT POWER.

Failure to disconnect input power before servicing can lead to serious injury, or death.
Disconnect input power before servicing.
Replace all parts and panels before reconnecting power and operating

DANGER – FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS, AND THE 
OWNER’S MANUAL MAY RESULT IN SERIOUS INJURY OR DEATH.

Содержание WPC2 T Series

















Отзывы: