background image

 

6

 

LEFT CURVE FOOTPRINT 

 

The purpose of this footprint is to serve as a GUIDELINE ONLY for approximate 
placement of the slide relative to the pool’s edge.  The actual dimensions after 
installation may vary according to the slope of the deck and the angle that the slide is 
oriented relative to the pool wall.  

YOU MUST FOLLOW THE INSTALLATION 

INSTRUCTIONS AS PRINTED IN THIS MANUAL

.

 

 

RIGHT CURVE FOOTPRINT 

 
 

The purpose of this footprint is to serve 
as a GUIDELINE ONLY for approximate 
placement of the slide relative to the 
pool’s edge. 
 
The actual dimensions after installation 
may vary according to the slope of the 
deck and the angle that the slide is 
oriented relative to the pool wall. 
 

YOU MUST FOLLOW THE 
INSTALLATION INSTRUCTIONS AS 
PRINTED IN THIS MANUAL. 

 
 
 
 
 
 

LEFT CURVE SLIDE WITH FLUSH DECK MOUNTING 
 

The purpose of this side view is to serve as a 
GUIDELINE ONLY for approximate placement of 
the slide relative to the deck.  The actual 
dimensions after installation may vary 
according to the slope of the deck and 
the angle that the slide is oriented 
relative to the pool wall.  When installing 
the slide in the deck, these dimensions 
will be reduced by at least 3-1/8 inches. 
 
HEIGHT ABOVE DECK LEVEL OF: LEFT 

CURVE RIGHT 

CURVE 

(A) Bottom of first ladder step: 

  11-1/2”  11-5/8” 

(B) 

Top 

runway 

surface: 

   78-3/8”  78-1/2” 

(C) Top runway side rail:   

 

 

83-3/4” 

 

83-3/4” 

(D) Top of handrail:   

 

  94-3/4”  94-3/4” 

(E) 

Exit 

runway 

surface: 

   12-7/8”  14” 

(F) Bottom of slide at exit 

end: 

  11-1/8”  11-7/8” 

NOTE: All dimensions are 
measured from the left side of 
the ladder foot (0”, 0”) 

FIGURE 4 

FIGURE 5

Содержание ROGUE GRAND RAPIDS





















Отзывы: