ST2-KP Keypad
1
2
3
4
5
The ST2-KP keypad is an in-wall single-gang keypad that is
designed to control the ST2 Dual Tuner (AM/FM/XM). It has a
backlit LCD panel and soft-touch control buttons.
Keypad Operation
Turning the keypad on/off
To activate the ST2-KP, press
. Press
to power
down the keypad display. The keypad remains powered
until the ST2 Tuner is turned off.
Selecting the desired tuner
To select a different tuner, press and hold
. (If the key-
pad has been hardware selected to Tuner 1 or Tuner 2, it
will not switch between the two tuners.) The backlight color
of the display will be green for Tuner 1 and amber for
Tuner 2. Each time a tuner is selected the display will
refresh with the current station or preset for that tuner, and
all subsequent button presses and memory preset entries
will be associated with that selected tuner.
Selecting the desired band (operating mode)
Push
to switch between AM/FM band, or XM operating
modes. Refer to the ST2-XM Tuner manual for mode
details.
Selecting the desired frequency
Use
and
for manual tuning (AM/FM) and channel
up and down (XM). To move quickly through the channels,
press and hold either
or
for more than 1.5 sec-
onds. European frequencies show in .05 MHz increments.
Recalling a Memory Preset
To recall a memory preset, press and release
or
to scroll through the presets for the selected bank.
(Memory presets must be stored for ST2-KP recall)
Selecting a Bank
To select a bank, select the desired tuner, then press and
hold
or
to select the desired bank. The bank
name will show on the display.
LCD PANEL - 5-character backlit display shows
frequency and band (messages scroll twice, then show first
5 characters)
FREQUENCY SELECT - Manual station tuning (European
frequencies show in .05 MHz increments)
BAND - Selects band (AM/FM); selects Operating Mode (XM)
POWER - Turns lighted keypad display on or off
TUNER SELECTION - Press and hold to select TUNER 1 or
TUNER 2 (unless jumper set for specific tuner)
BANK SELECT - Used for bank selection (press and hold)
MEM UP/DOWN - Scrolls through memory preset stations
for selected bank (press and release)
3
2
4
5
1
4
5
Warranty Repair
The Russound ST2-KP is fully guaranteed against all defects in materials and
workmanship for two (2) years from the date of purchase. During this period,
Russound will replace any defective parts and correct any defect in workman-
ship without charge for either parts or labor.
For this warranty to apply, the unit must be installed and used according to its
written instructions. If service is necessary, it must be performed by
Russound. The unit must be returned to Russound at the owner's expense and
with prior written permission. Accidental damage and shipping damage are
not considered defects, nor is damage resulting from abuse or from servicing
by an agency or person not specifically authorized in writing by Russound.
This Warranty does not cover: Damage caused by abuse, accident, misuse,
negligence, or improper installation or operation; Power surges and lightning
strikes; Normal wear and maintenance; Products that have been altered or
modified; Any product whose identifying number, decal, serial number, etc.
has been altered, defaced or removed.
Russound sells products only through authorized Dealers and Distributors to
ensure that customers obtain proper support and service. Any Russound prod-
uct purchased from an unauthorized dealer or other source, including retail-
ers, mail order sellers and online sellers will not be honored or serviced under
existing Russound warranty policy. Any sale of products by an unauthorized
source or other manner not authorized by Russound shall void the warranty on
the applicable product.
Damage to or destruction of components due to application of excessive
power voids the warranty on those parts. In these cases, repairs will be made
on the basis or the retail value of the parts and labor. To return for repairs,
the unit must be shipped to Russound at the owner's expense, along with a
note explaining the nature of service required. Be sure to pack the unit in a
corrugated container with at least three (3) inches of resilient material to pro-
tect the unit from damage in transit.
Before returning a unit for repair, call Russound at (603) 659-5170 for a
Return Authorization number. Write this number on the shipping label and ship
to: Russound, ATTN: Service, 5 Forbes Road, Newmarket, NH 03857
Due to continual efforts to improve product quality as new technology and
techniques become available, Russound/FMP, Inc. reserves the right to revise
system specifications without notice.
All trademarks are property of their respective owners.
ST2-KP Keypad-Front Panel
Technical Specifications
Dimensions:
1.875"W x 1.125"D x 4.3"H
(4.8 x 10.9 x 2.8 cm)
Fits 1 Gang UL/CSA Approved Junction Box
Weight:
5 oz. (141g)
Power Requirements: 12 VDC 150mA
CAT-5 Connection:
110 punchdown
5 Forbes Road, Newmarket, NH 03857
tel 603.659.5170 • fax 603.659.5388
e-mail: [email protected]
www.russound.com
DIAGN
(Diagnostics)
VER
(Version)
UDFRM
(Update
Firmware)
Displays current
firmware version
HOLD
BAND
After update
cycle Power
Start
Update
Cycle Power
Hold
This
Procedure
is for
Factory
use
ONLY
Utility Menu
The Utility Menu allows the installer to run a diagnostic
check on the keypad and to verify the firmware version.
The Utility Menu also contains the update firmware proce-
dure for updating the ST2-KP’s firmware. To access the
Utility Menu, press and release the Setup button on the
right side of the keypad. The menus are outlined in the
diagram at right. When finished, press and release the
Setup button until normal operating mode returns. If per-
forming Update Firmware, the power must be cycled.
Note:
For the ST2-KP to operate properly, the ST2 Tuner
must be configured with Tuner 1 as Source 1, and Tuner 2
as Source 2. If this is not the case, refer to the ST2 Tuner
Instruction Manual, Setup Menu section, to set source
numbers. Configure Tuner 1 as Source 1, and Tuner 2 as
Source 2.
Utility Menu for ST2-KP
2
