Operation
PlasmaWall XP Series Installation/Operation Manual
55
PRE
L
IMINAR
Y
Color Space:
Select Color Space from the Service menu to choose the color space of
the source signal for HDMI, RGB, and component connections.
• The default setting,
Auto
, functions as follows:
•
HDMI:
If the Auxiliary Video Information (AVI) infoframe contains color space and/or
range data, the PlasmaWall uses that information. Otherwise, for RGB sources, the
PlasmaWall uses the
RGB-Video
color space. For component SDTV and EDTV
resolutions,
REC601
is used. For other component video resolutions,
REC709
is
used.
•
RGB:
If Hsync or Vsync signals are present, the PlasmaWall uses the
RGB-PC
color
space. Otherwise,
REC601
is used for SDTV and EDTV sources, and
REC709
for
all other sources.
•
Component:
For SDTV and EDTV resolutions, the PlasmaWall uses the
REC601
color space. For all other resolutions, REC709 is used.
In most cases, the
Auto
setting determines the correct color space to use. If it does not,
you can force the PlasmaWall to use a specific color space. Choose one of the following:
•
REC709
sets the color space matrix to that defined in ITU-R BT.709.
•
REC601
sets the color space matrix to that defined in ITU-R BT.601.
•
RGB-PC
uses RGB color space and sets black at 0,0,0 RGB and white at
255,255,255 RGB, assuming an 8-bit image.
•
RGB-Video
uses RGB color space and sets black at 16,16,16 RGB and white at
235,235,235, assuming an 8-bit image, to correspond to the luminance values defined
in digital component standards.
Triggers:
Select Triggers from the Service menu to configure the 12-volt trigger outputs.
You can assign one or more trigger outputs to each aspect ratio. Those triggers are then
activated by selecting that aspect ratio.
Miscellaneous:
Select Miscellaneous from the Service menu to set the following options:
• Language:
Select Language from the Miscellaneous menu and press the up- or
down-arrows to select the OSD Language (English, Français, Deutsch, Italiano,
Español, Svenska, Traditional Chinese, Simplified Chinese, Português or Russian).
• OSD Timer:
Select OSD Timer from the Miscellaneous menu to set the OSD Timer,
which controls how long the menus remain on-screen after selecting them. Select from
5 to 60 seconds, in one-second increments. Or, set the timer to 0 (disabled) if you want
the menus to remain on-screen indefinitely.
• OSD Messages:
When you select a new aspect ratio, input source or memory preset,
the DHD Controller briefly displays an on-screen message confirming your new
selection. To prevent the display of these messages, select OSD Messages from the
Miscellaneous menu to and set it to Off.
• Blank Screen Color:
Select Blank Screen Color from the Miscellaneous menu to
select the color that appears when no incoming signal is present. The range is from 0
to 255 inclusive for each color component (red, green and blue).
• Sidebar Color:
Select Sidebar Color from the Miscellaneous menu to change the
color of the inactive image area. The range is from 0 to 255 inclusive for each color
component (red, green and blue). The inactive image area is on either side of the active
image area when using the 4:3 aspect ratio.
• Film Mode:
Use Film Mode to smooth out moving images from interlaced,
standard-definition (SD) sources. In most cases, the PlasmaWall detects the proper
“pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing
you may want to enable Film Mode to ensure stable processing for that source.
Содержание PlasmaWall XP-103DHD
