For example, we connect the RunCam Split Mini 2 to the UART 3 interface on the Flight
Controller: connect the Flight Controller to the computer, then open the configurator
software of the Flight Controller. (Open up the configurator that matches the firmware
you are running, Betaflight Configurator for Betaflight, Cleanflight Configurator for
Cleanflight). In the Peripherals column of the line UART3 (on the Ports tab), select
RunCam Device and click Save And Reboot.
In the Flight Controller Configurator, navigate to the Modes tab. There are new
CAMERA WI-FI, CAMERA POWER and CAMERA CHANGE modes
Assign any available channel to the function you need, for example:
·
CAMERA WI-FI: in the OSD of the camera, this is used to confirm your selection.
·
CAMERA POWER: start/stop the video. When in the OSD of the camera, this is used to
move to the next menu item.
·
CAMERA CHANGE MODE: switch among the two modes: video and OSD
setting mode. When in the OSD of the camera, this will exit the menu
·
Assign the AUX1 to the CAMERA WI-FI, range 1900-2100
·
Assign the AUX2 to the CAMERA POWER, range 1900-2100
·
Assign the AUX3 to the CAMERA CHANGE MODE, range 1900-2100
Please choose your Model on the controller, then access to the MIXER interface and
assign the channel to the switch of the controller. Take opentx 2.2.0 for example, assign
the channels CH5, CH6 and CH7 to SA, SB and SD respectively
Power the Flight Controller and the RunCam Split Mini 2
·
Set the SA to the bottom, the camera starts/stops the video
·
Set the SD to the bottom, the camera switches among the two modes:
video and OSD setting mode
www.runcam.com
Powering On/Off
Simultaneously press the Power/Shutter button and
Mode Switch button.
Camera Status Light:
Orange is On
• Press the Power/Shutter button to move to a setting.
• Short press the Mode Switch button to change setting.
• Long press the Mode Switch button to exit the menu.
Camera Status Light:
Blue blinks
Press the Power/Shutter button to start/stop recording.
In Standby Mode, long press the Mode Switch button to
cycle through the three modes: Video/Photos/OSD settings.
Long press the Power/Shutter button
Standby Mode
Camera Status Light:
Blue is On
Firmware
Upgrading
Camera Status Light:
Orange blinks
https://goo.gl/5Mq8zw
Mode Switching
Video Mode
OSD Setup Mode
Forced Shutdown
In standby mode, press the Mode Switch button three times
in rapid succession (within 2 seconds). When resetting is
complete, the status light (orange) blinks twice, and the
camera automatically shuts down.
Reset
Field of View(FOV)
Video Resolution
Video File Format
Image Resolution
TV Mode
Interface
Max Micro SD Card Supported
Dimensions
Power Input
Working Current
Weight
Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3)
1080@60fps/1080@50fps/1080@30fps/720@60fps
MOV
2 MP
NTSC (720*480)/PAL (720*576) Switchable
JST 1.25mm / UART
64G(need Class 6 or above,
recommend Class 10/UHS-I/UHS-II/UHS-III)
PCB 29*29mm / Lens Module 19*19mm
Hole Distance of Installation
20*20mm
DC 5-20V
(Non-direct power supply from battery,
Powered directly with battery will generate surges and
burn the camera.)
650mA @5V/270mA @12V
12.5g
Please visit:
https://support.runcam.com
Capacity up to 64GB; Please use high speed cards(Class10/UHS-I/UHS-II)
Please push the metal piece a little bit up with one hand like showed in above step 1
and then press the SD card(step 2) with another hand to let the card pop out.
Mode Switch Button
Power/Shutter Button
Sensor Connector
Metal Cover
RunCam
Video Transmitter
PDB
GND
Video
Power in
GND
5-20V
5-20V
UART Interface
FC
GND
GND
RX
RX
TX
TX
User Manual
·
Instruction Diagram
·
Micro SD Card
·
Basic Camera Operation
·
Transmitter Connection Diagram
·
Flight Controller Set
·
Technical Support
·
Parameter
Side A
Side B
Method One (Recommended):
Connect the Split mini PCB and the PDB with the
silicone cable
Method Two:
connect by the soldering pads
Preparation
·
Firmware: BetaFlight Firmware (≥3.2.0),CleanFlight Firmware(≥2.1.0) ,
KISS Firmware (≥1.3-RC30) or INAV Firmware (≥1.7.3).
·
Any available UART interface on the Flight Controller
1. Connect the RunCam Split Mini 2 with the UART interface of the Flight Controller
2. Make the Flight Controller recognize the RunCam Split Mini 2
3. Instructions of the functions of the camera and assigning transmitter channels
to them
4. Assign the channel to the switch of the controller
5. Test
1
2
Video Transmitter
PDB
GND
Video
Power in
GND
5-20V
VCC +
（
5-20V)
GND
Video
TX
RX
Microphone
2
MicroSD Card Slot
Warning:
Current Input ≥1A (Don't powered by VTx)
·
Lens Module Connection Diagram
NOTE:
To secure the connection of the cable, the metal cover must be installed.
