background image

·

App(Android | iOS)

     Search 'RunCam App' on Google Play/Apple Store, or download on our website:

     runcam.com/download/runcamSplit2S

     

Default SSID: 

RCSplit_ ****** (* for letters or numbers)

     

Default WiFi password: 

1234567890

Note: 

Recording automatically after turing on by default, with the V1.0 firmware, under 

            the video status, short press WIFI/MODE SWITCH button to pause/start the 
            recording. With the V1.1 and later firmware, under the video status, short press 
            WIFI/MODE SWITCH button to stop the recording and turn on the WIFI; Under the 
            standby mode, the function of the WIFI/MODE SWITCH button doesn't change.

·

Check Complete User Manual

      Please visit

runcam.com/download/runcamSplit2S

www.runcam.com

·

parameter

Field of View(FOV)

Lens Thread Size

Video Resolution

Video File Format

Image Resolution

TV Mode

Interface

Max Micro SD Card Supported

WiFi Module

Dimensions

Power Input

Working Current

Net Weight

FPV FOV 4:3@140°, 16:9@170°/HD Recording 170°

M12*0.5

1080@60fps/1080@50fps /1080@30fps/720@60fps

MOV

2 Megapixels

NTSC (720*480)/PAL (720*576) Switchable

Micro USB / UART
64G(need Class 6 or above, 

recommend Class 10/UHS-I/UHS-II/UHS-III)
Support (Removable)

PCB 38*38mm/Lens Module 19*19mm

DC 5V(USB)/DC 5-15V 

(Non-direct power supply 

from battery,Powered directly with battery will 

generate surges and burn the camera.)

650mA @5V / 270mA @12V

19g

User Manual

·

Instruction diagram

Side B

WiFi module connector

Power/Shutter Button

Micro-USB

Sensor connector

WiFi/Mode Switch Button

Side A

LED 1: 

Blue ——WiFi status light

LED 2: 

Green ——Photo mode status light

LED 3: 

Blue —— Video mode status light

LED 4: 

Orange —— OSD Setup status light

LED 5: 

Red —— Power status light, it's always on after being powered

TX
RX

GND

VCC+ (DC 5-15V)
GND
Video

LED 1
LED 2
LED 3
LED 4
LED 5

Microphone

Buzzer

·

5.8G Transmitter connection diagram

Preparation

· 

Firmware

BetaFlight Firmware (≥3.2.0),CleanFlight Firmware(≥2.1.0) ,

                      KISS Firmware (≥1.3-RC30) or INAV Firmware (≥1.7.3).

· 

Any available UART interface on the Flight Controller

1. Connect the RunCam Split with the UART interface of the Flight Controller

2. Make the Flight Controller recognize the Split

For example, we connect the Split to the UART 3 interface on the Flight Controller: 
connect the Flight Controller to the computer, then open the configurator software of 
the Flight Controller. (Open up the configurator that matches the firmware you are 
running, Betaflight Configurator for Betaflight, Cleanflight Configurator for Cleanflight). 
In the Peripherals column of the line UART3 (on the Ports tab), select RunCam Device 
and click Save And Reboot.

3.  Instructions of the functions of the camera and assigning transmitter 
     channels to them

In the Flight Controller Configurator, navigate to the Modes tab. There are new 

CAMERA WI-FI, CAMERA POWER and CAMERA CHANGE modes

.

·  

CAMERA WI-FI: turn on/off the WIFI of the camera. When in the OSD of the camera, this 

    is used to confirm your selection.

·  

CAMERA POWER: start/stop the video. When in the OSD of the camera, this is used to 

    move to the next menu item.

·  

CAMERA CHANGE MODE: switch among the three modes, video, photo and OSD 

    setting mode. When in the OSD of the camera, this will exit the menu.

Assign any available channel to the function you need, for example:

·  

Assign the AUX1 to the CAMERA WI-FI, range 1900-2100

·  

Assign the AUX2 to the CAMERA POWER, range 1900-2100

·  

Assign the AUX3 to the CAMERA CHANGE MODE, range 1900-2100

 

4. Assign the channel to the switch of the controller

Please choose your Model on the controller, then access to the Inputs interface and 
assign the channel to the switch of the controller. Take opentx 2.2.0 for example, assign 
the channels AUX5, AUX6 and AUX7 to sa, sb and sd respectively.

5. Test

Power the Flight Controller and the RunCam Split

·  

Set the SA to the bottom, the camera starts/stops the video

·  

Set the SB to the bottom, the camera turns on/off the WIFI

·  

Set the SD to the bottom, the camera switches among the three modes: video, photo 

    and OSD setting mode

·

Flight Controller Set

·

Basic Camera Operation

Powering On/Off
WiFi On/Off

Mode Switching

Video Mode

Photo Mode

OSD Setup Mode

Forced Shutdown

Reset

Long press the Power/Shutter button
Short press the WiFi/Mode Switch button

After powering on, long press the WiFi/Mode Switch button to cycle 
through the three modes: Video/Photos/OSD settings.

Camera Status Light: 

Blue (LED 3)

• Press the Power/Shutter button to start/stop recording.

Camera Status Light: 

Green (LED 2)

• Press the Power/Shutter button to capture photos.

Camera Status Light: 

Orange (LED 4)

• Press the Power/Shutter button to move to a setting. 
• Press the WiFi/Mode Switch button to select. 
• Long press the WiFi/Mode Switch button to exit the menu.

Simultaneously press the Power/Shutter button and 
WiFi/Mode Switch button.

In standby mode, press the WiFi/Mode Switch button three times in rapid 
succession (within 2 seconds). When resetting is complete, the status 
light (orange) blicks twice, and the camera automatically shuts down.

·

WiFi module connection diagram

Warning:

 

USB port only supports DC 5V

USB

DC 5V

(WiFi module)

·

MicroSD Card

     Capacity up to 64GB; Please use high speed cards(Class10/UHS-I/UHS-II).

·

Lens module connection diagram

5-15V

GND

Video

Power in

GND

 Transmitter

PDB

GND

GND

TX

TX

RX

RX

FC

UART Interface

2

1

2S

Warning:

 Please install the Metal Cover to make sure the Sensor Connector fixed steadily.

Отзывы: